diff --git a/doc/sphinx/Clusters_from_Scratch/active-active.rst b/doc/sphinx/Clusters_from_Scratch/active-active.rst index 96318fedee..933f1a9c99 100644 --- a/doc/sphinx/Clusters_from_Scratch/active-active.rst +++ b/doc/sphinx/Clusters_from_Scratch/active-active.rst @@ -1,294 +1,332 @@ .. index:: single: storage; active/active Convert Storage to Active/Active -------------------------------- The primary requirement for an Active/Active cluster is that the data required for your services is available, simultaneously, on both machines. Pacemaker makes no requirement on how this is achieved; you could use a SAN if you had one available, but since DRBD supports multiple Primaries, we can continue to use it here. .. index:: single: GFS2 single: DLM single: filesystem; GFS2 Install Cluster Filesystem Software ################################### The only hitch is that we need to use a cluster-aware filesystem. The one we used earlier with DRBD, xfs, is not one of those. Both OCFS2 and GFS2 are supported; here, we will use GFS2. On both nodes, install the GFS2 command-line utilities and the Distributed Lock Manager (DLM) required by cluster filesystems: .. code-block:: none # yum install -y gfs2-utils dlm +.. NOTE:: + + Because of `an open CentOS bug `_, + installing dlm is not trivial. This chapter will updated once the bug + is resolved. + Configure the Cluster for the DLM ################################# The DLM control daemon needs to run on both nodes, so we'll start by creating a resource for it (using the **ocf:pacemaker:controld** resource script), and clone it: .. code-block:: none [root@pcmk-1 ~]# pcs cluster cib dlm_cfg [root@pcmk-1 ~]# pcs -f dlm_cfg resource create dlm \ ocf:pacemaker:controld op monitor interval=60s [root@pcmk-1 ~]# pcs -f dlm_cfg resource clone dlm clone-max=2 clone-node-max=1 - [root@pcmk-1 ~]# pcs -f dlm_cfg resource show - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 - WebSite (ocf::heartbeat:apache): Started pcmk-1 - Master/Slave Set: WebDataClone [WebData] - Masters: [ pcmk-1 ] - Slaves: [ pcmk-2 ] - WebFS (ocf::heartbeat:Filesystem): Started pcmk-1 - Clone Set: dlm-clone [dlm] - Stopped: [ pcmk-1 pcmk-2 ] + [root@pcmk-1 ~]# pcs resource status + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + * WebSite (ocf::heartbeat:apache): Started pcmk-2 + * Clone Set: WebData-clone [WebData] (promotable): + * Masters: [ pcmk-2 ] + * Slaves: [ pcmk-1 ] + * WebFS (ocf::heartbeat:Filesystem): Started pcmk-2 + [root@pcmk-1 ~]# pcs resource config + Resource: ClusterIP (class=ocf provider=heartbeat type=IPaddr2) + Attributes: cidr_netmask=24 ip=192.168.122.120 + Operations: monitor interval=30s (ClusterIP-monitor-interval-30s) + start interval=0s timeout=20s (ClusterIP-start-interval-0s) + stop interval=0s timeout=20s (ClusterIP-stop-interval-0s) + Resource: WebSite (class=ocf provider=heartbeat type=apache) + Attributes: configfile=/etc/httpd/conf/httpd.conf statusurl=http://localhost/server-status + Operations: monitor interval=1min (WebSite-monitor-interval-1min) + start interval=0s timeout=40s (WebSite-start-interval-0s) + stop interval=0s timeout=60s (WebSite-stop-interval-0s) + Clone: WebData-clone + Meta Attrs: clone-max=2 clone-node-max=1 notify=true promotable=true promoted-max=1 promoted-node-max=1 + Resource: WebData (class=ocf provider=linbit type=drbd) + Attributes: drbd_resource=wwwdata + Operations: demote interval=0s timeout=90 (WebData-demote-interval-0s) + monitor interval=60s (WebData-monitor-interval-60s) + notify interval=0s timeout=90 (WebData-notify-interval-0s) + promote interval=0s timeout=90 (WebData-promote-interval-0s) + reload interval=0s timeout=30 (WebData-reload-interval-0s) + start interval=0s timeout=240 (WebData-start-interval-0s) + stop interval=0s timeout=100 (WebData-stop-interval-0s) + Resource: WebFS (class=ocf provider=heartbeat type=Filesystem) + Attributes: device=/dev/drbd1 directory=/var/www/html fstype=xfs + Operations: monitor interval=20s timeout=40s (WebFS-monitor-interval-20s) + start interval=0s timeout=60s (WebFS-start-interval-0s) + stop interval=0s timeout=60s (WebFS-stop-interval-0s) Activate our new configuration, and see how the cluster responds: .. code-block:: none [root@pcmk-1 ~]# pcs cluster cib-push dlm_cfg --config CIB updated [root@pcmk-1 ~]# pcs status Cluster name: mycluster - Stack: corosync - Current DC: pcmk-1 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Tue Sep 11 10:18:30 2018 - Last change: Tue Sep 11 10:16:49 2018 by hacluster via crmd on pcmk-2 - - 2 nodes configured - 8 resources configured - - Online: [ pcmk-1 pcmk-2 ] - - Full list of resources: - - ipmi-fencing (stonith:fence_ipmilan): Started pcmk-1 - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 - WebSite (ocf::heartbeat:apache): Started pcmk-1 - Master/Slave Set: WebDataClone [WebData] - Masters: [ pcmk-1 ] - Slaves: [ pcmk-2 ] - WebFS (ocf::heartbeat:Filesystem): Started pcmk-1 - Clone Set: dlm-clone [dlm] - Started: [ pcmk-1 pcmk-2 ] + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-1 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Wed Feb 3 09:29:21 2021 + * Last change: Wed Feb 3 09:29:17 2021 by root via cibadmin on pcmk-1 + * 2 nodes configured + * 7 resource instances configured + + Node List: + * Online: [ pcmk-1 pcmk-2 ] + + Full List of Resources: + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + * WebSite (ocf::heartbeat:apache): Started pcmk-2 + * Clone Set: WebData-clone [WebData] (promotable): + * Masters: [ pcmk-2 ] + * Slaves: [ pcmk-1 ] + * WebFS (ocf::heartbeat:Filesystem): Started pcmk-2 + * Clone Set: dlm-clone [dlm]: + * Stopped: [ pcmk-1 pcmk-2 ] + + Failed Resource Actions: + * dlm_monitor_0 on pcmk-2 'not installed' (5): call=40, status='complete', exitreason='Setup problem: couldn't find command: dlm_controld', last-rc-change='2021-02-03 09:29:18 -05:00', queued=0ms, exec=26ms + * dlm_monitor_0 on pcmk-1 'not installed' (5): call=43, status='complete', exitreason='Setup problem: couldn't find command: dlm_controld', last-rc-change='2021-02-03 09:29:18 -05:00', queued=0ms, exec=30ms Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled +.. NOTE:: + + Once the aforementioned CentOS bug is resolved, there won't be any failed + resource actions. Create and Populate GFS2 Filesystem ################################### Before we do anything to the existing partition, we need to make sure it is unmounted. We do this by telling the cluster to stop the WebFS resource. This will ensure that other resources (in our case, Apache) using WebFS are not only stopped, but stopped in the correct order. .. code-block:: none [root@pcmk-1 ~]# pcs resource disable WebFS [root@pcmk-1 ~]# pcs resource ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 WebSite (ocf::heartbeat:apache): Stopped Master/Slave Set: WebDataClone [WebData] Masters: [ pcmk-1 ] Slaves: [ pcmk-2 ] WebFS (ocf::heartbeat:Filesystem): Stopped (disabled) Clone Set: dlm-clone [dlm] Started: [ pcmk-1 pcmk-2 ] You can see that both Apache and WebFS have been stopped, and that **pcmk-1** is the current master for the DRBD device. Now we can create a new GFS2 filesystem on the DRBD device. .. WARNING:: This will erase all previous content stored on the DRBD device. Ensure you have a copy of any important data. .. IMPORTANT:: Run the next command on whichever node has the DRBD Primary role. Otherwise, you will receive the message: .. code-block:: none /dev/drbd1: Read-only file system .. code-block:: none [root@pcmk-1 ~]# mkfs.gfs2 -p lock_dlm -j 2 -t mycluster:web /dev/drbd1 It appears to contain an existing filesystem (xfs) This will destroy any data on /dev/drbd1 Are you sure you want to proceed? [y/n] y Discarding device contents (may take a while on large devices): Done Adding journals: Done Building resource groups: Done Creating quota file: Done Writing superblock and syncing: Done Device: /dev/drbd1 Block size: 4096 Device size: 0.50 GB (131059 blocks) Filesystem size: 0.50 GB (131056 blocks) Journals: 2 Resource groups: 3 Locking protocol: "lock_dlm" Lock table: "mycluster:web" UUID: 0bcbffab-cada-4105-94d1-be8a26669ee0 The ``mkfs.gfs2`` command required a number of additional parameters: * ``-p lock_dlm`` specifies that we want to use the kernel's DLM. * ``-j 2`` indicates that the filesystem should reserve enough space for two journals (one for each node that will access the filesystem). * ``-t mycluster:web`` specifies the lock table name. The format for this field is ``:``. For ``CLUSTERNAME``, we need to use the same value we specified originally with ``pcs cluster setup --name`` (which is also the value of **cluster_name** in ``/etc/corosync/corosync.conf``). If you are unsure what your cluster name is, you can look in ``/etc/corosync/corosync.conf`` or execute the command ``pcs cluster corosync pcmk-1 | grep cluster_name``. Now we can (re-)populate the new filesystem with data (web pages). We'll create yet another variation on our home page. .. code-block:: none [root@pcmk-1 ~]# mount /dev/drbd1 /mnt [root@pcmk-1 ~]# cat <<-END >/mnt/index.html My Test Site - GFS2 END [root@pcmk-1 ~]# chcon -R --reference=/var/www/html /mnt [root@pcmk-1 ~]# umount /dev/drbd1 [root@pcmk-1 ~]# drbdadm verify wwwdata Reconfigure the Cluster for GFS2 ################################ With the WebFS resource stopped, let's update the configuration. .. code-block:: none [root@pcmk-1 ~]# pcs resource show WebFS Resource: WebFS (class=ocf provider=heartbeat type=Filesystem) Attributes: device=/dev/drbd1 directory=/var/www/html fstype=xfs Meta Attrs: target-role=Stopped Operations: monitor interval=20 timeout=40 (WebFS-monitor-interval-20) notify interval=0s timeout=60 (WebFS-notify-interval-0s) start interval=0s timeout=60 (WebFS-start-interval-0s) stop interval=0s timeout=60 (WebFS-stop-interval-0s) The fstype option needs to be updated to **gfs2** instead of **xfs**. .. code-block:: none [root@pcmk-1 ~]# pcs resource update WebFS fstype=gfs2 [root@pcmk-1 ~]# pcs resource show WebFS Resource: WebFS (class=ocf provider=heartbeat type=Filesystem) Attributes: device=/dev/drbd1 directory=/var/www/html fstype=gfs2 Meta Attrs: target-role=Stopped Operations: monitor interval=20 timeout=40 (WebFS-monitor-interval-20) notify interval=0s timeout=60 (WebFS-notify-interval-0s) start interval=0s timeout=60 (WebFS-start-interval-0s) stop interval=0s timeout=60 (WebFS-stop-interval-0s) GFS2 requires that DLM be running, so we also need to set up new colocation and ordering constraints for it: .. code-block:: none [root@pcmk-1 ~]# pcs constraint colocation add WebFS with dlm-clone INFINITY [root@pcmk-1 ~]# pcs constraint order dlm-clone then WebFS Adding dlm-clone WebFS (kind: Mandatory) (Options: first-action=start then-action=start) .. index:: pair: filesystem; clone Clone the Filesystem Resource ############################# Now that we have a cluster filesystem ready to go, we can configure the cluster so both nodes mount the filesystem. Clone the filesystem resource in a new configuration. Notice how pcs automatically updates the relevant constraints again. .. code-block:: none [root@pcmk-1 ~]# pcs cluster cib active_cfg [root@pcmk-1 ~]# pcs -f active_cfg resource clone WebFS [root@pcmk-1 ~]# pcs -f active_cfg constraint Location Constraints: Ordering Constraints: start ClusterIP then start WebSite (kind:Mandatory) promote WebDataClone then start WebFS-clone (kind:Mandatory) start WebFS-clone then start WebSite (kind:Mandatory) start dlm-clone then start WebFS-clone (kind:Mandatory) Colocation Constraints: WebSite with ClusterIP (score:INFINITY) WebFS-clone with WebDataClone (score:INFINITY) (with-rsc-role:Master) WebSite with WebFS-clone (score:INFINITY) WebFS-clone with dlm-clone (score:INFINITY) Ticket Constraints: Tell the cluster that it is now allowed to promote both instances to be DRBD Primary (aka. master). .. code-block:: none [root@pcmk-1 ~]# pcs -f active_cfg resource update WebDataClone master-max=2 Finally, load our configuration to the cluster, and re-enable the WebFS resource (which we disabled earlier). .. code-block:: none [root@pcmk-1 ~]# pcs cluster cib-push active_cfg --config CIB updated [root@pcmk-1 ~]# pcs resource enable WebFS After all the processes are started, the status should look similar to this. .. code-block:: none [root@pcmk-1 ~]# pcs resource Master/Slave Set: WebDataClone [WebData] Masters: [ pcmk-1 pcmk-2 ] Clone Set: dlm-clone [dlm] Started: [ pcmk-1 pcmk-2 ] ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 Clone Set: WebFS-clone [WebFS] Started: [ pcmk-1 pcmk-2 ] WebSite (ocf::heartbeat:apache): Started pcmk-1 Test Failover ############# Testing failover is left as an exercise for the reader. With this configuration, the data is now active/active. The website administrator could change HTML files on either node, and the live website will show the changes even if it is running on the opposite node. If the web server is configured to listen on all IP addresses, it is possible to remove the constraints between the WebSite and ClusterIP resources, and clone the WebSite resource. The web server would always be ready to serve web pages, and only the IP address would need to be moved in a failover. diff --git a/doc/sphinx/Clusters_from_Scratch/active-passive.rst b/doc/sphinx/Clusters_from_Scratch/active-passive.rst index f68f881240..4a2a83a9c3 100644 --- a/doc/sphinx/Clusters_from_Scratch/active-passive.rst +++ b/doc/sphinx/Clusters_from_Scratch/active-passive.rst @@ -1,276 +1,280 @@ Create an Active/Passive Cluster -------------------------------- .. index:: pair: resource; IP address Add a Resource ############## Our first resource will be a unique IP address that the cluster can bring up on either node. Regardless of where any cluster service(s) are running, end users need a consistent address to contact them on. Here, I will choose 192.168.122.120 as the floating address, give it the imaginative name ClusterIP and tell the cluster to check whether it is running every 30 seconds. .. WARNING:: The chosen address must not already be in use on the network. Do not reuse an IP address one of the nodes already has configured. .. code-block:: none [root@pcmk-1 ~]# pcs resource create ClusterIP ocf:heartbeat:IPaddr2 \ ip=192.168.122.120 cidr_netmask=24 op monitor interval=30s Another important piece of information here is **ocf:heartbeat:IPaddr2**. This tells Pacemaker three things about the resource you want to add: * The first field (**ocf** in this case) is the standard to which the resource script conforms and where to find it. * The second field (**heartbeat** in this case) is standard-specific; for OCF resources, it tells the cluster which OCF namespace the resource script is in. * The third field (**IPaddr2** in this case) is the name of the resource script. To obtain a list of the available resource standards (the **ocf** part of **ocf:heartbeat:IPaddr2**), run: .. code-block:: none [root@pcmk-1 ~]# pcs resource standards lsb ocf service systemd To obtain a list of the available OCF resource providers (the **heartbeat** part of **ocf:heartbeat:IPaddr2**), run: .. code-block:: none [root@pcmk-1 ~]# pcs resource providers heartbeat openstack pacemaker Finally, if you want to see all the resource agents available for a specific OCF provider (the **IPaddr2** part of **ocf:heartbeat:IPaddr2**), run: .. code-block:: none [root@pcmk-1 ~]# pcs resource agents ocf:heartbeat apache aws-vpc-move-ip + aws-vpc-route53 awseip awsvip - azure-lb - clvm + azure-events . . (skipping lots of resources to save space) . symlink tomcat + vdo-vol VirtualDomain Xinetd Now, verify that the IP resource has been added, and display the cluster's status to see that it is now active: .. code-block:: none [root@pcmk-1 ~]# pcs status Cluster name: mycluster - Stack: corosync - Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Mon Sep 10 16:55:26 2018 - Last change: Mon Sep 10 16:53:42 2018 by root via cibadmin on pcmk-1 - - 2 nodes configured - 1 resource configured - - Online: [ pcmk-1 pcmk-2 ] - - Full list of resources: - - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-2 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Tue Jan 26 19:22:10 2021 + * Last change: Tue Jan 26 19:20:28 2021 by root via cibadmin on pcmk-1 + * 2 nodes configured + * 1 resource instance configured + + Node List: + * Online: [ pcmk-1 pcmk-2 ] + + Full List of Resources: + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled Perform a Failover ################## Since our ultimate goal is high availability, we should test failover of our new resource before moving on. First, find the node on which the IP address is running. .. code-block:: none [root@pcmk-1 ~]# pcs status Cluster name: mycluster - Stack: corosync - Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Mon Sep 10 16:55:26 2018 - Last change: Mon Sep 10 16:53:42 2018 by root via cibadmin on pcmk-1 - - 2 nodes configured - 1 resource configured - - Online: [ pcmk-1 pcmk-2 ] - - Full list of resources: - - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-2 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Tue Jan 26 19:22:10 2021 + * Last change: Tue Jan 26 19:20:28 2021 by root via cibadmin on pcmk-1 + * 2 nodes configured + * 1 resource instance configured + + Node List: + * Online: [ pcmk-1 pcmk-2 ] + + Full List of Resources: + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 You can see that the status of the **ClusterIP** resource is **Started** on a particular node (in this example, **pcmk-1**). Shut down Pacemaker and Corosync on that machine to trigger a failover. .. code-block:: none [root@pcmk-1 ~]# pcs cluster stop pcmk-1 - Stopping Cluster (pacemaker)... - Stopping Cluster (corosync)... + pcmk-1: Stopping Cluster (pacemaker)... + pcmk-1: Stopping Cluster (corosync)... .. NOTE:: A cluster command such as ``pcs cluster stop `` can be run from any node in the cluster, not just the affected node. Verify that pacemaker and corosync are no longer running: .. code-block:: none [root@pcmk-1 ~]# pcs status - Error: cluster is not currently running on this node + Error: error running crm_mon, is pacemaker running? + Could not connect to the CIB: Transport endpoint is not connected + crm_mon: Error: cluster is not available on this node Go to the other node, and check the cluster status. .. code-block:: none - [root@pcmk-2 ~]# pcs status + [root@pcmk-1 ~]# pcs status Cluster name: mycluster - Stack: corosync - Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Mon Sep 10 16:57:22 2018 - Last change: Mon Sep 10 16:53:42 2018 by root via cibadmin on pcmk-1 - - 2 nodes configured - 1 resource configured - - Online: [ pcmk-2 ] - OFFLINE: [ pcmk-1 ] - - Full list of resources: - - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-2 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Tue Jan 26 19:25:26 2021 + * Last change: Tue Jan 26 19:20:28 2021 by root via cibadmin on pcmk-1 + * 2 nodes configured + * 1 resource instance configured + + Node List: + * Online: [ pcmk-2 ] + * OFFLINE: [ pcmk-1 ] + + Full List of Resources: + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled Notice that **pcmk-1** is **OFFLINE** for cluster purposes (its **pcsd** is still active, allowing it to receive ``pcs`` commands, but it is not participating in the cluster). Also notice that **ClusterIP** is now running on **pcmk-2** -- failover happened automatically, and no errors are reported. .. topic:: Quorum If a cluster splits into two (or more) groups of nodes that can no longer - communicate with each other (aka. _partitions_), _quorum_ is used to prevent + communicate with each other (aka. *partitions*), *quorum* is used to prevent resources from starting on more nodes than desired, which would risk data corruption. A cluster has quorum when more than half of all known nodes are online in the same partition, or for the mathematically inclined, whenever the following equation is true: .. code-block:: none total_nodes < 2 * active_nodes For example, if a 5-node cluster split into 3- and 2-node paritions, the 3-node partition would have quorum and could continue serving resources. If a 6-node cluster split into two 3-node partitions, neither partition would have quorum; pacemaker's default behavior in such cases is to stop all resources, in order to prevent data corruption. Two-node clusters are a special case. By the above definition, a two-node cluster would only have quorum when both nodes are running. This would make the creation of a two-node cluster pointless, but corosync has the ability to treat two-node clusters as if only one node is required for quorum. The ``pcs cluster setup`` command will automatically configure **two_node: 1** in ``corosync.conf``, so a two-node cluster will "just work". If you are using a different cluster shell, you will have to configure ``corosync.conf`` appropriately yourself. Now, simulate node recovery by restarting the cluster stack on **pcmk-1**, and check the cluster's status. (It may take a little while before the cluster gets going on the node, but it eventually will look like the below.) .. code-block:: none [root@pcmk-1 ~]# pcs cluster start pcmk-1 pcmk-1: Starting Cluster... [root@pcmk-1 ~]# pcs status Cluster name: mycluster - Stack: corosync - Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Mon Sep 10 17:00:04 2018 - Last change: Mon Sep 10 16:53:42 2018 by root via cibadmin on pcmk-1 - - 2 nodes configured - 1 resource configured - - Online: [ pcmk-1 pcmk-2 ] - - Full list of resources: - - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-2 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Tue Jan 26 19:28:30 2021 + * Last change: Tue Jan 26 19:28:27 2021 by root via cibadmin on pcmk-1 + * 2 nodes configured + * 1 resource instance configured + + Node List: + * Online: [ pcmk-1 pcmk-2 ] + + Full List of Resources: + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled .. index:: stickiness Prevent Resources from Moving after Recovery ############################################ In most circumstances, it is highly desirable to prevent healthy resources from being moved around the cluster. Moving resources almost always requires a period of downtime. For complex services such as databases, this period can be quite long. To address this, Pacemaker has the concept of resource *stickiness*, which controls how strongly a service prefers to stay running where it is. You may like to think of it as the "cost" of any downtime. By default, Pacemaker assumes there is zero cost associated with moving resources and will do so to achieve "optimal" [#]_ resource placement. We can specify a different stickiness for every resource, but it is often sufficient to change the default. .. code-block:: none - [root@pcmk-1 ~]# pcs resource defaults resource-stickiness=100 + [root@pcmk-1 ~]# pcs resource defaults update resource-stickiness=100 Warning: Defaults do not apply to resources which override them with their own defined values [root@pcmk-1 ~]# pcs resource defaults - resource-stickiness: 100 + Meta Attrs: rsc_defaults-meta_attributes + resource-stickiness=100 .. [#] Pacemaker's definition of optimal may not always agree with that of a human's. The order in which Pacemaker processes lists of resources and nodes creates implicit preferences in situations where the administrator has not explicitly specified them. diff --git a/doc/sphinx/Clusters_from_Scratch/ap-configuration.rst b/doc/sphinx/Clusters_from_Scratch/ap-configuration.rst index 32c472abf6..adba12ca68 100644 --- a/doc/sphinx/Clusters_from_Scratch/ap-configuration.rst +++ b/doc/sphinx/Clusters_from_Scratch/ap-configuration.rst @@ -1,372 +1,378 @@ Configuration Recap ------------------- Final Cluster Configuration ########################### +.. NOTE:: + + Because of `an open CentOS bug `_, + installing dlm is not trivial. This chapter will updated once the bug + is resolved. + .. code-block:: none [root@pcmk-1 ~]# pcs resource Master/Slave Set: WebDataClone [WebData] Masters: [ pcmk-1 pcmk-2 ] Clone Set: dlm-clone [dlm] Started: [ pcmk-1 pcmk-2 ] ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 Clone Set: WebFS-clone [WebFS] Started: [ pcmk-1 pcmk-2 ] WebSite (ocf::heartbeat:apache): Started pcmk-1 .. code-block:: none [root@pcmk-1 ~]# pcs resource op defaults timeout: 240s .. code-block:: none [root@pcmk-1 ~]# pcs stonith - impi-fencing (stonith:fence_ipmilan): Started pcmk-1 + * my_stonith (stonith:fence_virt): Started pcmk-1 .. code-block:: none [root@pcmk-1 ~]# pcs constraint Location Constraints: Ordering Constraints: start ClusterIP then start WebSite (kind:Mandatory) promote WebDataClone then start WebFS-clone (kind:Mandatory) start WebFS-clone then start WebSite (kind:Mandatory) start dlm-clone then start WebFS-clone (kind:Mandatory) Colocation Constraints: WebSite with ClusterIP (score:INFINITY) WebFS-clone with WebDataClone (score:INFINITY) (with-rsc-role:Master) WebSite with WebFS-clone (score:INFINITY) WebFS-clone with dlm-clone (score:INFINITY) Ticket Constraints: .. code-block:: none [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync Current DC: pcmk-1 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum Last updated: Tue Sep 11 10:41:53 2018 Last change: Tue Sep 11 10:40:16 2018 by root via cibadmin on pcmk-1 2 nodes configured 11 resources configured Online: [ pcmk-1 pcmk-2 ] Full list of resources: - ipmi-fencing (stonith:fence_ipmilan): Started pcmk-1 + my_stonith (stonith:fence_virt): Started pcmk-1 Master/Slave Set: WebDataClone [WebData] Masters: [ pcmk-1 pcmk-2 ] Clone Set: dlm-clone [dlm] Started: [ pcmk-1 pcmk-2 ] ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 Clone Set: WebFS-clone [WebFS] Started: [ pcmk-1 pcmk-2 ] WebSite (ocf::heartbeat:apache): Started pcmk-1 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled .. code-block:: none [root@pcmk-1 ~]# pcs cluster cib --config .. code-block:: xml Node List ######### .. code-block:: none [root@pcmk-1 ~]# pcs status nodes Pacemaker Nodes: Online: pcmk-1 pcmk-2 Standby: Maintenance: Offline: Pacemaker Remote Nodes: Online: Standby: Maintenance: Offline: Cluster Options ############### .. code-block:: none [root@pcmk-1 ~]# pcs property Cluster Properties: cluster-infrastructure: corosync cluster-name: mycluster dc-version: 1.1.18-11.el7_5.3-2b07d5c5a9 have-watchdog: false last-lrm-refresh: 1536679009 stonith-enabled: true The output shows state information automatically obtained about the cluster, including: * **cluster-infrastructure** - the cluster communications layer in use * **cluster-name** - the cluster name chosen by the administrator when the cluster was created * **dc-version** - the version (including upstream source-code hash) of Pacemaker used on the Designated Controller, which is the node elected to determine what actions are needed when events occur The output also shows options set by the administrator that control the way the cluster operates, including: * **stonith-enabled=true** - whether the cluster is allowed to use STONITH resources Resources ######### Default Options _______________ .. code-block:: none [root@pcmk-1 ~]# pcs resource defaults resource-stickiness: 100 This shows cluster option defaults that apply to every resource that does not explicitly set the option itself. Above: * **resource-stickiness** - Specify the aversion to moving healthy resources to other machines Fencing _______ .. code-block:: none [root@pcmk-1 ~]# pcs stonith show - ipmi-fencing (stonith:fence_ipmilan): Started pcmk-1 - [root@pcmk-1 ~]# pcs stonith show ipmi-fencing - Resource: ipmi-fencing (class=stonith type=fence_ipmilan) + * my_stonith (stonith:fence_virt): Started pcmk-1 + [root@pcmk-1 ~]# pcs stonith show my_stonith + Resource: my_stonith (class=stonith type=fence_virt) Attributes: ipaddr="10.0.0.1" login="testuser" passwd="acd123" pcmk_host_list="pcmk-1 pcmk-2" Operations: monitor interval=60s (fence-monitor-interval-60s) Service Address _______________ Users of the services provided by the cluster require an unchanging address with which to access it. .. code-block:: none [root@pcmk-1 ~]# pcs resource show ClusterIP Resource: ClusterIP (class=ocf provider=heartbeat type=IPaddr2) Attributes: cidr_netmask=24 ip=192.168.122.120 clusterip_hash=sourceip Meta Attrs: resource-stickiness=0 Operations: monitor interval=30s (ClusterIP-monitor-interval-30s) start interval=0s timeout=20s (ClusterIP-start-interval-0s) stop interval=0s timeout=20s (ClusterIP-stop-interval-0s) DRBD - Shared Storage _____________________ Here, we define the DRBD service and specify which DRBD resource (from /etc/drbd.d/\*.res) it should manage. We make it a master clone resource and, in order to have an active/active setup, allow both instances to be promoted to master at the same time. We also set the notify option so that the cluster will tell DRBD agent when its peer changes state. .. code-block:: none [root@pcmk-1 ~]# pcs resource show WebDataClone Master: WebDataClone Meta Attrs: master-node-max=1 clone-max=2 notify=true master-max=2 clone-node-max=1 Resource: WebData (class=ocf provider=linbit type=drbd) Attributes: drbd_resource=wwwdata Operations: demote interval=0s timeout=90 (WebData-demote-interval-0s) monitor interval=60s (WebData-monitor-interval-60s) notify interval=0s timeout=90 (WebData-notify-interval-0s) promote interval=0s timeout=90 (WebData-promote-interval-0s) reload interval=0s timeout=30 (WebData-reload-interval-0s) start interval=0s timeout=240 (WebData-start-interval-0s) stop interval=0s timeout=100 (WebData-stop-interval-0s) [root@pcmk-1 ~]# pcs constraint ref WebDataClone Resource: WebDataClone colocation-WebFS-WebDataClone-INFINITY order-WebDataClone-WebFS-mandatory Cluster Filesystem __________________ The cluster filesystem ensures that files are read and written correctly. We need to specify the block device (provided by DRBD), where we want it mounted and that we are using GFS2. Again, it is a clone because it is intended to be active on both nodes. The additional constraints ensure that it can only be started on nodes with active DLM and DRBD instances. .. code-block:: none [root@pcmk-1 ~]# pcs resource show WebFS-clone Clone: WebFS-clone Resource: WebFS (class=ocf provider=heartbeat type=Filesystem) Attributes: device=/dev/drbd1 directory=/var/www/html fstype=gfs2 Operations: monitor interval=20 timeout=40 (WebFS-monitor-interval-20) notify interval=0s timeout=60 (WebFS-notify-interval-0s) start interval=0s timeout=60 (WebFS-start-interval-0s) stop interval=0s timeout=60 (WebFS-stop-interval-0s) [root@pcmk-1 ~]# pcs constraint ref WebFS-clone Resource: WebFS-clone colocation-WebFS-WebDataClone-INFINITY colocation-WebSite-WebFS-INFINITY colocation-WebFS-dlm-clone-INFINITY order-WebDataClone-WebFS-mandatory order-WebFS-WebSite-mandatory order-dlm-clone-WebFS-mandatory Apache ______ Lastly, we have the actual service, Apache. We need only tell the cluster where to find its main configuration file and restrict it to running on a node that has the required filesystem mounted and the IP address active. .. code-block:: none [root@pcmk-1 ~]# pcs resource show WebSite Resource: WebSite (class=ocf provider=heartbeat type=apache) Attributes: configfile=/etc/httpd/conf/httpd.conf statusurl=http://localhost/server-status Operations: monitor interval=1min (WebSite-monitor-interval-1min) start interval=0s timeout=40s (WebSite-start-interval-0s) stop interval=0s timeout=60s (WebSite-stop-interval-0s) [root@pcmk-1 ~]# pcs constraint ref WebSite Resource: WebSite colocation-WebSite-ClusterIP-INFINITY colocation-WebSite-WebFS-INFINITY order-ClusterIP-WebSite-mandatory order-WebFS-WebSite-mandatory diff --git a/doc/sphinx/Clusters_from_Scratch/apache.rst b/doc/sphinx/Clusters_from_Scratch/apache.rst index 0a6d696fcf..6b955b244a 100644 --- a/doc/sphinx/Clusters_from_Scratch/apache.rst +++ b/doc/sphinx/Clusters_from_Scratch/apache.rst @@ -1,450 +1,452 @@ .. index:: single: Apache HTTP Server Add Apache HTTP Server as a Cluster Service ------------------------------------------- Now that we have a basic but functional active/passive two-node cluster, we're ready to add some real services. We're going to start with Apache HTTP Server because it is a feature of many clusters and relatively simple to configure. Install Apache ############## Before continuing, we need to make sure Apache is installed on both hosts. We also need the wget tool in order for the cluster to be able to check the status of the Apache server. .. code-block:: none # yum install -y httpd wget # firewall-cmd --permanent --add-service=http # firewall-cmd --reload .. IMPORTANT:: Do **not** enable the httpd service. Services that are intended to be managed via the cluster software should never be managed by the OS. It is often useful, however, to manually start the service, verify that it works, then stop it again, before adding it to the cluster. This allows you to resolve any non-cluster-related problems before continuing. Since this is a simple example, we'll skip that step here. Create Website Documents ######################## We need to create a page for Apache to serve. On |CFS_DISTRO| |CFS_DISTRO_VER|, the default Apache document root is /var/www/html, so we'll create an index file there. For the moment, we will simplify things by serving a static site and manually synchronizing the data between the two nodes, so run this command on both nodes: .. code-block:: none # cat <<-END >/var/www/html/index.html My Test Site - $(hostname) END .. index:: single: Apache HTTP Server; status URL Enable the Apache status URL ############################ In order to monitor the health of your Apache instance, and recover it if it fails, the resource agent used by Pacemaker assumes the server-status URL is available. On both nodes, enable the URL with: .. code-block:: none # cat <<-END >/etc/httpd/conf.d/status.conf SetHandler server-status Require local END .. NOTE:: If you are using a different operating system, server-status may already be enabled or may be configurable in a different location. If you are using a version of Apache HTTP Server less than 2.4, the syntax will be different. .. index:: pair: Apache HTTP Server; resource Configure the Cluster ##################### At this point, Apache is ready to go, and all that needs to be done is to add it to the cluster. Let's call the resource WebSite. We need to use an OCF resource script called apache in the heartbeat namespace [#]_. The script's only required parameter is the path to the main Apache configuration file, and we'll tell the cluster to check once a minute that Apache is still running. .. code-block:: none [root@pcmk-1 ~]# pcs resource create WebSite ocf:heartbeat:apache \ configfile=/etc/httpd/conf/httpd.conf \ statusurl="http://localhost/server-status" \ op monitor interval=1min By default, the operation timeout for all resources' start, stop, and monitor operations is 20 seconds. In many cases, this timeout period is less than a particular resource's advised timeout period. For the purposes of this tutorial, we will adjust the global operation timeout default to 240 seconds. .. code-block:: none - [root@pcmk-1 ~]# pcs resource op defaults timeout=240s + [root@pcmk-1 ~]# pcs resource op defaults update timeout=240s Warning: Defaults do not apply to resources which override them with their own defined values [root@pcmk-1 ~]# pcs resource op defaults timeout: 240s .. NOTE:: In a production cluster, it is usually better to adjust each resource's start, stop, and monitor timeouts to values that are appropriate to the behavior observed in your environment, rather than adjust the global default. After a short delay, we should see the cluster start Apache. .. code-block:: none [root@pcmk-1 ~]# pcs status Cluster name: mycluster - Stack: corosync - Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Mon Sep 10 17:06:22 2018 - Last change: Mon Sep 10 17:05:41 2018 by root via cibadmin on pcmk-1 - - 2 nodes configured - 2 resources configured - - Online: [ pcmk-1 pcmk-2 ] - - Full list of resources: - - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 - WebSite (ocf::heartbeat:apache): Started pcmk-1 + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-2 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Tue Jan 26 19:38:22 2021 + * Last change: Tue Jan 26 19:38:19 2021 by root via cibadmin on pcmk-1 + * 2 nodes configured + * 2 resource instances configured + + Node List: + * Online: [ pcmk-1 pcmk-2 ] + + Full List of Resources: + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + * WebSite (ocf::heartbeat:apache): Started pcmk-1 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled Wait a moment, the WebSite resource isn't running on the same host as our IP address! .. NOTE:: If, in the ``pcs status`` output, you see the WebSite resource has failed to start, then you've likely not enabled the status URL correctly. You can check whether this is the problem by running: .. code-block:: none wget -O - http://localhost/server-status If you see **Not Found** or **Forbidden** in the output, then this is likely the problem. Ensure that the **** block is correct. .. index:: single: constraint; colocation single: colocation constraint Ensure Resources Run on the Same Host ##################################### To reduce the load on any one machine, Pacemaker will generally try to spread the configured resources across the cluster nodes. However, we can tell the cluster that two resources are related and need to run on the same host (or not at all). Here, we instruct the cluster that WebSite can only run on the host that ClusterIP is active on. To achieve this, we use a *colocation constraint* that indicates it is mandatory for WebSite to run on the same node as ClusterIP. The "mandatory" part of the colocation constraint is indicated by using a score of INFINITY. The INFINITY score also means that if ClusterIP is not active anywhere, WebSite will not be permitted to run. .. NOTE:: If ClusterIP is not active anywhere, WebSite will not be permitted to run anywhere. .. IMPORTANT:: Colocation constraints are "directional", in that they imply certain things about the order in which the two resources will have a location chosen. In this case, we're saying that **WebSite** needs to be placed on the same machine as **ClusterIP**, which implies that the cluster must know the location of **ClusterIP** before choosing a location for **WebSite**. .. code-block:: none [root@pcmk-1 ~]# pcs constraint colocation add WebSite with ClusterIP INFINITY [root@pcmk-1 ~]# pcs constraint Location Constraints: Ordering Constraints: Colocation Constraints: WebSite with ClusterIP (score:INFINITY) Ticket Constraints: [root@pcmk-1 ~]# pcs status Cluster name: mycluster - Stack: corosync - Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Mon Sep 10 17:08:54 2018 - Last change: Mon Sep 10 17:08:27 2018 by root via cibadmin on pcmk-1 + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-2 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Tue Jan 26 19:45:11 2021 + * Last change: Tue Jan 26 19:44:30 2021 by root via cibadmin on pcmk-1 + * 2 nodes configured + * 2 resource instances configured + + Node List: + * Online: [ pcmk-1 pcmk-2 ] + + Full List of Resources: + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + * WebSite (ocf::heartbeat:apache): Started pcmk-2 - 2 nodes configured - 2 resources configured - - Online: [ pcmk-1 pcmk-2 ] - - Full list of resources: - - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 - WebSite (ocf::heartbeat:apache): Started pcmk-2 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled .. index:: single: constraint; ordering single: ordering constraint Ensure Resources Start and Stop in Order ######################################## Like many services, Apache can be configured to bind to specific IP addresses on a host or to the wildcard IP address. If Apache binds to the wildcard, it doesn't matter whether an IP address is added before or after Apache starts; Apache will respond on that IP just the same. However, if Apache binds only to certain IP address(es), the order matters: If the address is added after Apache starts, Apache won't respond on that address. To be sure our WebSite responds regardless of Apache's address configuration, we need to make sure ClusterIP not only runs on the same node, but starts before WebSite. A colocation constraint only ensures the resources run together, not the order in which they are started and stopped. We do this by adding an ordering constraint. By default, all order constraints are mandatory, which means that the recovery of ClusterIP will also trigger the recovery of WebSite. .. code-block:: none [root@pcmk-1 ~]# pcs constraint order ClusterIP then WebSite Adding ClusterIP WebSite (kind: Mandatory) (Options: first-action=start then-action=start) [root@pcmk-1 ~]# pcs constraint Location Constraints: Ordering Constraints: start ClusterIP then start WebSite (kind:Mandatory) Colocation Constraints: WebSite with ClusterIP (score:INFINITY) Ticket Constraints: .. index:: single: constraint; location single: location constraint Prefer One Node Over Another ############################ Pacemaker does not rely on any sort of hardware symmetry between nodes, so it may well be that one machine is more powerful than the other. In such cases, you may want to host the resources on the more powerful node when it is available, to have the best performance -- or you may want to host -the resources on the _less_ powerful node when it's available, so you don't +the resources on the **less** powerful node when it's available, so you don't have to worry about whether you can handle the load after a failover. To do this, we create a location constraint. In the location constraint below, we are saying the WebSite resource prefers the node pcmk-1 with a score of 50. Here, the score indicates how strongly we'd like the resource to run at this location. .. code-block:: none [root@pcmk-1 ~]# pcs constraint location WebSite prefers pcmk-1=50 [root@pcmk-1 ~]# pcs constraint Location Constraints: Resource: WebSite Enabled on: pcmk-1 (score:50) Ordering Constraints: start ClusterIP then start WebSite (kind:Mandatory) Colocation Constraints: WebSite with ClusterIP (score:INFINITY) Ticket Constraints: [root@pcmk-1 ~]# pcs status Cluster name: mycluster - Stack: corosync - Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Mon Sep 10 17:21:41 2018 - Last change: Mon Sep 10 17:21:14 2018 by root via cibadmin on pcmk-1 - - 2 nodes configured - 2 resources configured - - Online: [ pcmk-1 pcmk-2 ] - - Full list of resources: - - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 - WebSite (ocf::heartbeat:apache): Started pcmk-2 + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-2 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Tue Jan 26 19:46:52 2021 + * Last change: Tue Jan 26 19:46:40 2021 by root via cibadmin on pcmk-1 + * 2 nodes configured + * 2 resource instances configured + + Node List: + * Online: [ pcmk-1 pcmk-2 ] + + Full List of Resources: + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + * WebSite (ocf::heartbeat:apache): Started pcmk-2 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled Wait a minute, the resources are still on pcmk-2! Even though WebSite now prefers to run on pcmk-1, that preference is (intentionally) less than the resource stickiness (how much we preferred not to have unnecessary downtime). To see the current placement scores, you can use a tool called crm_simulate. .. code-block:: none [root@pcmk-1 ~]# crm_simulate -sL Current cluster status: Online: [ pcmk-1 pcmk-2 ] ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 WebSite (ocf::heartbeat:apache): Started pcmk-2 Allocation scores: native_color: ClusterIP allocation score on pcmk-1: 50 native_color: ClusterIP allocation score on pcmk-2: 200 native_color: WebSite allocation score on pcmk-1: -INFINITY native_color: WebSite allocation score on pcmk-2: 100 Transition Summary: .. index:: single: resource; moving manually Move Resources Manually ####################### There are always times when an administrator needs to override the cluster and force resources to move to a specific location. In this example, we will force the WebSite to move to pcmk-1. We will use the **pcs resource move** command to create a temporary constraint with a score of INFINITY. While we could update our existing constraint, using **move** allows to easily get rid of the temporary constraint later. If desired, we could even give a lifetime for the constraint, so it would expire automatically -- but we don't do that in this example. .. code-block:: none [root@pcmk-1 ~]# pcs resource move WebSite pcmk-1 [root@pcmk-1 ~]# pcs constraint Location Constraints: Resource: WebSite Enabled on: pcmk-1 (score:50) Enabled on: pcmk-1 (score:INFINITY) (role: Started) Ordering Constraints: start ClusterIP then start WebSite (kind:Mandatory) Colocation Constraints: WebSite with ClusterIP (score:INFINITY) Ticket Constraints: [root@pcmk-1 ~]# pcs status Cluster name: mycluster - Stack: corosync - Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Mon Sep 10 17:28:55 2018 - Last change: Mon Sep 10 17:28:27 2018 by root via crm_resource on pcmk-1 - - 2 nodes configured - 2 resources configured - - Online: [ pcmk-1 pcmk-2 ] - - Full list of resources: - - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 - WebSite (ocf::heartbeat:apache): Started pcmk-1 + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-2 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Tue Jan 26 19:49:27 2021 + * Last change: Tue Jan 26 19:49:10 2021 by root via crm_resource on pcmk-1 + * 2 nodes configured + * 2 resource instances configured + + Node List: + * Online: [ pcmk-1 pcmk-2 ] + + Full List of Resources: + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + * WebSite (ocf::heartbeat:apache): Started pcmk-1 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled Once we've finished whatever activity required us to move the resources to pcmk-1 (in our case nothing), we can then allow the cluster to resume normal operation by removing the new constraint. Due to our first location constraint and our default stickiness, the resources will remain on pcmk-1. We will use the **pcs resource clear** command, which removes all temporary constraints previously created by **pcs resource move** or **pcs resource ban**. .. code-block:: none [root@pcmk-1 ~]# pcs resource clear WebSite + Removing constraint: cli-prefer-WebSite [root@pcmk-1 ~]# pcs constraint Location Constraints: Resource: WebSite Enabled on: pcmk-1 (score:50) Ordering Constraints: start ClusterIP then start WebSite (kind:Mandatory) Colocation Constraints: WebSite with ClusterIP (score:INFINITY) Ticket Constraints: Note that the INFINITY location constraint is now gone. If we check the cluster status, we can also see that (as expected) the resources are still active on pcmk-1. .. code-block:: none [root@pcmk-1 ~]# pcs status Cluster name: mycluster - Stack: corosync - Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Mon Sep 10 17:31:47 2018 - Last change: Mon Sep 10 17:31:04 2018 by root via crm_resource on pcmk-1 - - 2 nodes configured - 2 resources configured - - Online: [ pcmk-1 pcmk-2 ] - - Full list of resources: - - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 - WebSite (ocf::heartbeat:apache): Started pcmk-1 + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-2 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Tue Jan 26 19:50:52 2021 + * Last change: Tue Jan 26 19:50:24 2021 by root via crm_resource on pcmk-1 + * 2 nodes configured + * 2 resource instances configured + + Node List: + * Online: [ pcmk-1 pcmk-2 ] + + Full List of Resources: + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + * WebSite (ocf::heartbeat:apache): Started pcmk-1 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled To remove the constraint with the score of 50, we would first get the constraint's ID using **pcs constraint --full**, then remove it with **pcs constraint remove** and the ID. We won't show those steps here, but feel free to try it on your own, with the help of the pcs man page if necessary. .. [#] Compare the key used here, **ocf:heartbeat:apache**, with the one we used earlier for the IP address, **ocf:heartbeat:IPaddr2** diff --git a/doc/sphinx/Clusters_from_Scratch/cluster-setup.rst b/doc/sphinx/Clusters_from_Scratch/cluster-setup.rst index abb632c985..56939c00e1 100644 --- a/doc/sphinx/Clusters_from_Scratch/cluster-setup.rst +++ b/doc/sphinx/Clusters_from_Scratch/cluster-setup.rst @@ -1,334 +1,299 @@ Set up a Cluster ---------------- Simplify Administration With a Cluster Shell ############################################ In the dark past, configuring Pacemaker required the administrator to read and write XML. In true UNIX style, there were also a number of different commands that specialized in different aspects of querying and updating the cluster. In addition, the various components of the cluster stack (corosync, pacemaker, etc.) had to be configured separately, with different configuration tools and formats. All of that has been greatly simplified with the creation of higher-level tools, whether command-line or GUIs, that hide all the mess underneath. Command-line cluster shells take all the individual aspects required for managing and configuring a cluster, and pack them into one simple-to-use command-line tool. They even allow you to queue up several changes at once and commit them all at once. Two popular command-line shells are ``pcs`` and ``crmsh``. Clusters from Scratch is based on ``pcs`` because it comes with CentOS, but both have similar functionality. Choosing a shell or GUI is a matter of personal preference and what comes with (and perhaps is supported by) your choice of operating system. Install the Cluster Software ############################ -Fire up a shell on both nodes and run the following to install pacemaker, pcs, -and some other command-line tools that will make our lives easier: +Fire up a shell on both nodes and run the following to activate the High +Availability repo. .. code-block:: none - # yum install -y pacemaker pcs psmisc policycoreutils-python + # dnf config-manager --set-enabled ha .. IMPORTANT:: This document will show commands that need to be executed on both nodes with a simple ``#`` prompt. Be sure to run them on each node individually. +Now, we'll install pacemaker, pcs, and some other command-line tools that will +make our lives easier: + +.. code-block:: none + + # yum install -y pacemaker pcs psmisc policycoreutils-python3 + .. NOTE:: This document uses ``pcs`` for cluster management. Other alternatives, such as ``crmsh``, are available, but their syntax will differ from the examples used here. Configure the Cluster Software ############################## .. index:: single: firewall Allow cluster services through firewall _______________________________________ On each node, allow cluster-related services through the local firewall: .. code-block:: none # firewall-cmd --permanent --add-service=high-availability success # firewall-cmd --reload success .. NOTE :: If you are using iptables directly, or some other firewall solution besides firewalld, simply open the following ports, which can be used by various clustering components: TCP ports 2224, 3121, and 21064, and UDP port 5405. If you run into any problems during testing, you might want to disable the firewall and SELinux entirely until you have everything working. This may create significant security issues and should not be performed on machines that will be exposed to the outside world, but may be appropriate during development and testing on a protected host. To disable security measures: .. code-block:: none [root@pcmk-1 ~]# setenforce 0 [root@pcmk-1 ~]# sed -i.bak "s/SELINUX=enforcing/SELINUX=permissive/g" /etc/selinux/config [root@pcmk-1 ~]# systemctl mask firewalld.service [root@pcmk-1 ~]# systemctl stop firewalld.service [root@pcmk-1 ~]# iptables --flush Enable pcs Daemon _________________ Before the cluster can be configured, the pcs daemon must be started and enabled to start at boot time on each node. This daemon works with the pcs command-line interface to manage synchronizing the corosync configuration across all nodes in the cluster. Start and enable the daemon by issuing the following commands on each node: .. code-block:: none # systemctl start pcsd.service # systemctl enable pcsd.service Created symlink from /etc/systemd/system/multi-user.target.wants/pcsd.service to /usr/lib/systemd/system/pcsd.service. The installed packages will create a **hacluster** user with a disabled password. While this is fine for running ``pcs`` commands locally, the account needs a login password in order to perform such tasks as syncing the corosync configuration, or starting and stopping the cluster on other nodes. This tutorial will make use of such commands, so now we will set a password for the **hacluster** user, using the same password on both nodes: .. code-block:: none # passwd hacluster Changing password for user hacluster. New password: Retype new password: passwd: all authentication tokens updated successfully. .. NOTE:: Alternatively, to script this process or set the password on a different machine from the one you're logged into, you can use the ``--stdin`` option for ``passwd``: .. code-block:: none [root@pcmk-1 ~]# ssh pcmk-2 -- 'echo mysupersecretpassword | passwd --stdin hacluster' Configure Corosync __________________ -On either node, use ``pcs cluster auth`` to authenticate as the **hacluster** user: +On either node, use ``pcs host auth`` to authenticate as the **hacluster** user: .. code-block:: none - [root@pcmk-1 ~]# pcs cluster auth pcmk-1 pcmk-2 + [root@pcmk-1 ~]# pcs host auth pcmk-1 pcmk-2 Username: hacluster Password: pcmk-2: Authorized pcmk-1: Authorized -.. NOTE:: - - In Fedora 29 and CentOS 8.0, the command has been changed to ``pcs host auth``: - - .. code-block:: none - - [root@pcmk-1 ~]# pcs host auth pcmk-1 pcmk-2 - Username: hacluster - Password: - pcmk-2: Authorized - pcmk-1: Authorized - Next, use ``pcs cluster setup`` on the same node to generate and synchronize the corosync configuration: .. code-block:: none - [root@pcmk-1 ~]# pcs cluster setup --name mycluster pcmk-1 pcmk-2 - Destroying cluster on nodes: pcmk-1, pcmk-2... - pcmk-2: Stopping Cluster (pacemaker)... - pcmk-1: Stopping Cluster (pacemaker)... - pcmk-1: Successfully destroyed cluster + [root@pcmk-1 ~]# pcs cluster setup mycluster pcmk-1 pcmk-2 + No addresses specified for host 'pcmk-1', using 'pcmk-1' + No addresses specified for host 'pcmk-2', using 'pcmk-2' + Destroying cluster on hosts: 'pcmk-1', 'pcmk-2'... pcmk-2: Successfully destroyed cluster - - Sending 'pacemaker_remote authkey' to 'pcmk-1', 'pcmk-2' - pcmk-2: successful distribution of the file 'pacemaker_remote authkey' - pcmk-1: successful distribution of the file 'pacemaker_remote authkey' - Sending cluster config files to the nodes... - pcmk-1: Succeeded - pcmk-2: Succeeded - - Synchronizing pcsd certificates on nodes pcmk-1, pcmk-2... - pcmk-2: Success - pcmk-1: Success - Restarting pcsd on the nodes in order to reload the certificates... - pcmk-2: Success - pcmk-1: Success - -.. NOTE :: - In Fedora 29 and CentOS 8.0, the syntax has been changed and the ``--name`` option - has been dropped: - - .. code-block:: none - - [root@pcmk-1 ~]# pcs cluster setup mycluster pcmk-1 pcmk-2 - No addresses specified for host 'pcmk-1', using 'pcmk-1' - No addresses specified for host 'pcmk-2', using 'pcmk-2' - Destroying cluster on hosts: 'pcmk-1', 'pcmk-2'... - pcmk-1: Successfully destroyed cluster - pcmk-2: Successfully destroyed cluster - Requesting remove 'pcsd settings' from 'pcmk-1', 'pcmk-2' - pcmk-1: successful removal of the file 'pcsd settings' - pcmk-2: successful removal of the file 'pcsd settings' - Sending 'corosync authkey', 'pacemaker authkey' to 'pcmk-1', 'pcmk-2' - pcmk-2: successful distribution of the file 'corosync authkey' - pcmk-2: successful distribution of the file 'pacemaker authkey' - pcmk-1: successful distribution of the file 'corosync authkey' - pcmk-1: successful distribution of the file 'pacemaker authkey' - Synchronizing pcsd SSL certificates on nodes 'pcmk-1', 'pcmk-2'... - pcmk-1: Success - pcmk-2: Success - Sending 'corosync.conf' to 'pcmk-1', 'pcmk-2' - pcmk-2: successful distribution of the file 'corosync.conf' - pcmk-1: successful distribution of the file 'corosync.conf' - Cluster has been successfully set up. + pcmk-1: Successfully destroyed cluster + Requesting remove 'pcsd settings' from 'pcmk-1', 'pcmk-2' + pcmk-1: successful removal of the file 'pcsd settings' + pcmk-2: successful removal of the file 'pcsd settings' + Sending 'corosync authkey', 'pacemaker authkey' to 'pcmk-1', 'pcmk-2' + pcmk-1: successful distribution of the file 'corosync authkey' + pcmk-1: successful distribution of the file 'pacemaker authkey' + pcmk-2: successful distribution of the file 'corosync authkey' + pcmk-2: successful distribution of the file 'pacemaker authkey' + Sending 'corosync.conf' to 'pcmk-1', 'pcmk-2' + pcmk-1: successful distribution of the file 'corosync.conf' + pcmk-2: successful distribution of the file 'corosync.conf' + Cluster has been successfully set up. If you received an authorization error for either of those commands, make sure you configured the **hacluster** user account on each node with the same password. -.. NOTE:: - - If you are not using ``pcs`` for cluster administration, - follow whatever procedures are appropriate for your tools - to create a corosync.conf and copy it to all nodes. - - The ``pcs`` command will configure corosync to use UDP unicast transport; if you - choose to use multicast instead, choose a multicast address carefully [#]_. - The final corosync.conf configuration on each node should look something like the sample in :ref:`sample-corosync-configuration`. Explore pcs ########### Start by taking some time to familiarize yourself with what ``pcs`` can do. .. code-block:: none [root@pcmk-1 ~]# pcs - + Usage: pcs [-f file] [-h] [commands]... Control and configure pacemaker and corosync. - + Options: -h, --help Display usage and exit. -f file Perform actions on file instead of active CIB. + Commands supporting the option use the initial state of + the specified file as their input and then overwrite the + file with the state reflecting the requested + operation(s). + A few commands only use the specified file in read-only + mode since their effect is not a CIB modification. --debug Print all network traffic and external commands run. --version Print pcs version information. List pcs capabilities if --full is specified. --request-timeout Timeout for each outgoing request to another node in seconds. Default is 60s. --force Override checks and errors, the exact behavior depends on the command. WARNING: Using the --force option is strongly discouraged unless you know what you are doing. Commands: cluster Configure cluster options and nodes. resource Manage cluster resources. stonith Manage fence devices. constraint Manage resource constraints. property Manage pacemaker properties. acl Manage pacemaker access control lists. qdevice Manage quorum device provider on the local host. quorum Manage cluster quorum settings. booth Manage booth (cluster ticket manager). status View cluster status. config View and manage cluster configuration. pcsd Manage pcs daemon. + host Manage hosts known to pcs/pcsd. node Manage cluster nodes. alert Manage pacemaker alerts. + client Manage pcsd client configuration. + dr Manage disaster recovery configuration. + tag Manage pacemaker tags. + As you can see, the different aspects of cluster management are separated into categories. To discover the functionality available in each of these categories, one can issue the command ``pcs help``. Below is an example of all the options available under the status category. .. code-block:: none [root@pcmk-1 ~]# pcs status help - + Usage: pcs status [commands]... View current cluster and resource status Commands: - [status] [--full | --hide-inactive] + [status] [--full] [--hide-inactive] View all information about the cluster and resources (--full provides more details, --hide-inactive hides inactive resources). - - resources [ | --full | --groups | --hide-inactive] - Show all currently configured resources or if a resource is specified - show the options for the configured resource. If --full is specified, - all configured resource options will be displayed. If --groups is - specified, only show groups (and their resources). If --hide-inactive + + resources [--hide-inactive] + Show status of all currently configured resources. If --hide-inactive is specified, only show active resources. - - groups - View currently configured groups and their resources. - + cluster View current cluster status. - + corosync View current membership information as seen by corosync. - + quorum View current quorum status. qdevice [--full] [] Show runtime status of specified model of quorum device provider. Using --full will give more detailed output. If is specified, only information about the specified cluster will be displayed. - + + booth + Print current status of booth on the local node. + nodes [corosync | both | config] View current status of nodes from pacemaker. If 'corosync' is specified, view current status of nodes from corosync instead. If 'both' is specified, view current status of nodes from both corosync & pacemaker. If 'config' is specified, print nodes from corosync & pacemaker configuration. - + pcsd []... Show current status of pcsd on nodes specified, or on all nodes configured in the local cluster if no nodes are specified. - + xml View xml version of status (output from crm_mon -r -1 -X). Additionally, if you are interested in the version and supported cluster stack(s) available with your Pacemaker installation, run: .. code-block:: none [root@pcmk-1 ~]# pacemakerd --features - Pacemaker 1.1.18-11.el7_5.3 (Build: 2b07d5c5a9) - Supporting v3.0.14: generated-manpages agent-manpages ncurses libqb-logging libqb-ipc systemd nagios corosync-native atomic-attrd acls + Pacemaker 2.0.5-4.el8 (Build: ba59be7122) + Supporting v3.6.1: generated-manpages agent-manpages ncurses libqb-logging libqb-ipc systemd nagios corosync-native atomic-attrd acls cibsecrets + .. [#] For some subtle issues, see `Topics in High-Performance Messaging: Multicast Address Assignment `_ or the more detailed treatment in `Cisco's Guidelines for Enterprise IP Multicast Address Allocation `_. diff --git a/doc/sphinx/Clusters_from_Scratch/fencing.rst b/doc/sphinx/Clusters_from_Scratch/fencing.rst index 25975e0eab..14fe088b06 100644 --- a/doc/sphinx/Clusters_from_Scratch/fencing.rst +++ b/doc/sphinx/Clusters_from_Scratch/fencing.rst @@ -1,224 +1,237 @@ .. index:: fencing Configure Fencing ----------------- What is Fencing? ################ Fencing protects your data from being corrupted, and your application from becoming unavailable, due to unintended concurrent access by rogue nodes. Just because a node is unresponsive doesn't mean it has stopped accessing your data. The only way to be 100% sure that your data is safe, is to use fencing to ensure that the node is truly offline before allowing the data to be accessed from another node. Fencing also has a role to play in the event that a clustered service cannot be stopped. In this case, the cluster uses fencing to force the whole node offline, thereby making it safe to start the service elsewhere. Fencing is also known as STONITH, an acronym for "Shoot The Other Node In The Head", since the most popular form of fencing is cutting a host's power. In order to guarantee the safety of your data [#]_, fencing is enabled by default. .. NOTE:: It is possible to tell the cluster not to use fencing, by setting the **stonith-enabled** cluster option to false: .. code-block:: none [root@pcmk-1 ~]# pcs property set stonith-enabled=false [root@pcmk-1 ~]# crm_verify -L However, this is completely inappropriate for a production cluster. It tells the cluster to simply pretend that failed nodes are safely powered off. Some vendors will refuse to support clusters that have fencing disabled. Even disabling it for a test cluster means you won't be able to test real failure scenarios. .. index:: single: fencing; device Choose a Fence Device ##################### The two broad categories of fence device are power fencing, which cuts off power to the target, and fabric fencing, which cuts off the target's access to some critical resource, such as a shared disk or access to the local network. Power fencing devices include: * Intelligent power switches * IPMI * Hardware watchdog device (alone, or in combination with shared storage used as a "poison pill" mechanism) Fabric fencing devices include: * Shared storage that can be cut off for a target host by another host (for example, an external storage device that supports SCSI-3 persistent reservations) * Intelligent network switches Using IPMI as a power fencing device may seem like a good choice. However, if the IPMI shares power and/or network access with the host (such as most onboard IPMI controllers), a power or network failure will cause both the host and its fencing device to fail. The cluster will be unable to recover, and must stop all resources to avoid a possible split-brain situation. Likewise, any device that relies on the machine being active (such as SSH-based "devices" sometimes used during testing) is inappropriate, because fencing will be required when the node is completely unresponsive. Configure the Cluster for Fencing ################################# #. Install the fence agent(s). To see what packages are available, run ``yum search fence-``. Be sure to install the package(s) on all cluster nodes. #. Configure the fence device itself to be able to fence your nodes and accept fencing requests. This includes any necessary configuration on the device and on the nodes, and any firewall or SELinux changes needed. Test the communication between the device and your nodes. #. Find the name of the correct fence agent: ``pcs stonith list`` #. Find the parameters associated with the device: ``pcs stonith describe `` #. Create a local copy of the CIB: ``pcs cluster cib stonith_cfg`` #. Create the fencing resource: ``pcs -f stonith_cfg stonith create [STONITH_DEVICE_OPTIONS]`` Any flags that do not take arguments, such as ``--ssl``, should be passed as ``ssl=1``. #. Enable fencing in the cluster: ``pcs -f stonith_cfg property set stonith-enabled=true`` #. If the device does not know how to fence nodes based on their cluster node name, you may also need to set the special **pcmk_host_map** parameter. See ``man pacemaker-fenced`` for details. #. If the device does not support the **list** command, you may also need to set the special **pcmk_host_list** and/or **pcmk_host_check** parameters. See ``man pacemaker-fenced`` for details. #. If the device does not expect the victim to be specified with the **port** parameter, you may also need to set the special **pcmk_host_argument** parameter. See ``man pacemaker-fenced`` for details. #. Commit the new configuration: ``pcs cluster cib-push stonith_cfg`` #. Once the fence device resource is running, test it (you might want to stop the cluster on that machine first): ``stonith_admin --reboot `` Example ####### For this example, assume we have a chassis containing four nodes and a separately powered IPMI device active on 10.0.0.1. Following the steps above would go something like this: Step 1: Install the **fence-agents-ipmilan** package on both nodes. Step 2: Configure the IP address, authentication credentials, etc. in the IPMI device itself. Step 3: Choose the **fence_ipmilan** STONITH agent. Step 4: Obtain the agent's possible parameters: .. code-block:: none [root@pcmk-1 ~]# pcs stonith describe fence_ipmilan fence_ipmilan - Fence agent for IPMI - + fence_ipmilan is an I/O Fencing agentwhich can be used with machines controlled by IPMI.This agent calls support software ipmitool (http://ipmitool.sf.net/). WARNING! This fence agent might report success before the node is powered off. You should use -m/method onoff if your fence device works correctly with that option. Stonith options: - ipport: TCP/UDP port to use for connection with device - hexadecimal_kg: Hexadecimal-encoded Kg key for IPMIv2 authentication - port: IP address or hostname of fencing device (together with --port-as-ip) - inet6_only: Forces agent to use IPv6 addresses only - ipaddr: IP Address or Hostname - passwd_script: Script to retrieve password - method: Method to fence (onoff|cycle) - inet4_only: Forces agent to use IPv4 addresses only - passwd: Login password or passphrase - lanplus: Use Lanplus to improve security of connection auth: IPMI Lan Auth type. cipher: Ciphersuite to use (same as ipmitool -C parameter) - target: Bridge IPMI requests to the remote target address + hexadecimal_kg: Hexadecimal-encoded Kg key for IPMIv2 authentication + ip: IP address or hostname of fencing device + ipport: TCP/UDP port to use for connection with device + lanplus: Use Lanplus to improve security of connection + method: Method to fence + password: Login password or passphrase + password_script: Script to run to retrieve password + plug: IP address or hostname of fencing device (together with --port-as-ip) privlvl: Privilege level on IPMI device - timeout: Timeout (sec) for IPMI operation - login: Login Name - verbose: Verbose mode - debug: Write debug information to given file - power_wait: Wait X seconds after issuing ON/OFF - login_timeout: Wait X seconds for cmd prompt after login + target: Bridge IPMI requests to the remote target address + username: Login name + quiet: Disable logging to stderr. Does not affect --verbose or --debug-file or logging to syslog. + verbose: Verbose mode. Multiple -v flags can be stacked on the command line (e.g., -vvv) to increase + verbosity. + verbose_level: Level of debugging detail in output. Defaults to the number of --verbose flags specified + on the command line, or to 1 if verbose=1 in a stonith device configuration (i.e., on + stdin). + debug_file: Write debug information to given file delay: Wait X seconds before fencing is started - power_timeout: Test X seconds for status change after ON/OFF + disable_timeout: Disable timeout (true/false) (default: true when run from Pacemaker 2.0+) ipmitool_path: Path to ipmitool binary - shell_timeout: Wait X seconds for cmd prompt after issuing command + login_timeout: Wait X seconds for cmd prompt after login port_as_ip: Make "port/plug" to be an alias to IP address + power_timeout: Test X seconds for status change after ON/OFF + power_wait: Wait X seconds after issuing ON/OFF + shell_timeout: Wait X seconds for cmd prompt after issuing command retry_on: Count of attempts to retry power on - sudo: Use sudo (without password) when calling 3rd party sotfware. - priority: The priority of the stonith resource. Devices are tried in order of highest priority to lowest. - pcmk_host_map: A mapping of host names to ports numbers for devices that do not support host names. Eg. node1:1;node2:2,3 would tell the cluster to use port 1 for node1 and ports 2 and - 3 for node2 - pcmk_host_list: A list of machines controlled by this device (Optional unless pcmk_host_check=static-list). - pcmk_host_check: How to determine which machines are controlled by the device. Allowed values: dynamic-list (query the device), static-list (check the pcmk_host_list attribute), none - (assume every device can fence every machine) - pcmk_delay_max: Enable a random delay for stonith actions and specify the maximum of random delay. This prevents double fencing when using slow devices such as sbd. Use this to enable a - random delay for stonith actions. The overall delay is derived from this random delay value adding a static delay so that the sum is kept below the maximum delay. - pcmk_delay_base: Enable a base delay for stonith actions and specify base delay value. This prevents double fencing when different delays are configured on the nodes. Use this to enable - a static delay for stonith actions. The overall delay is derived from a random delay value adding this static delay so that the sum is kept below the maximum delay. - pcmk_action_limit: The maximum number of actions can be performed in parallel on this device Pengine property concurrent-fencing=true needs to be configured first. Then use this to - specify the maximum number of actions can be performed in parallel on this device. -1 is unlimited. - + use_sudo: Use sudo (without password) when calling 3rd party software + sudo_path: Path to sudo binary + pcmk_host_map: A mapping of host names to ports numbers for devices that do not support host names. Eg. + node1:1;node2:2,3 would tell the cluster to use port 1 for node1 and ports 2 and 3 for + node2 + pcmk_host_list: A list of machines controlled by this device (Optional unless pcmk_host_check=static- + list). + pcmk_host_check: How to determine which machines are controlled by the device. Allowed values: dynamic- + list (query the device via the 'list' command), static-list (check the pcmk_host_list + attribute), status (query the device via the 'status' command), none (assume every + device can fence every machine) + pcmk_delay_max: Enable a random delay for stonith actions and specify the maximum of random delay. This + prevents double fencing when using slow devices such as sbd. Use this to enable a + random delay for stonith actions. The overall delay is derived from this random delay + value adding a static delay so that the sum is kept below the maximum delay. + pcmk_delay_base: Enable a base delay for stonith actions and specify base delay value. This prevents + double fencing when different delays are configured on the nodes. Use this to enable a + static delay for stonith actions. The overall delay is derived from a random delay + value adding this static delay so that the sum is kept below the maximum delay. + pcmk_action_limit: The maximum number of actions can be performed in parallel on this device Cluster + property concurrent-fencing=true needs to be configured first. Then use this to + specify the maximum number of actions can be performed in parallel on this device. + -1 is unlimited. + Default operations: monitor: interval=60s Step 5: ``pcs cluster cib stonith_cfg`` Step 6: Here are example parameters for creating our fence device resource: .. code-block:: none [root@pcmk-1 ~]# pcs -f stonith_cfg stonith create ipmi-fencing fence_ipmilan \ pcmk_host_list="pcmk-1 pcmk-2" ipaddr=10.0.0.1 login=testuser \ passwd=acd123 op monitor interval=60s [root@pcmk-1 ~]# pcs -f stonith_cfg stonith - ipmi-fencing (stonith:fence_ipmilan): Stopped + * ipmi-fencing (stonith:fence_ipmilan): Stopped Steps 7-10: Enable fencing in the cluster: .. code-block:: none [root@pcmk-1 ~]# pcs -f stonith_cfg property set stonith-enabled=true [root@pcmk-1 ~]# pcs -f stonith_cfg property Cluster Properties: cluster-infrastructure: corosync cluster-name: mycluster - dc-version: 1.1.18-11.el7_5.3-2b07d5c5a9 + dc-version: 2.0.5-4.el8-ba59be7122 have-watchdog: false stonith-enabled: true Step 11: ``pcs cluster cib-push stonith_cfg --config`` Step 12: Test: .. code-block:: none [root@pcmk-1 ~]# pcs cluster stop pcmk-2 [root@pcmk-1 ~]# stonith_admin --reboot pcmk-2 After a successful test, login to any rebooted nodes, and start the cluster (with ``pcs cluster start``). .. [#] If the data is corrupt, there is little point in continuing to make it available. diff --git a/doc/sphinx/Clusters_from_Scratch/images/Console.png b/doc/sphinx/Clusters_from_Scratch/images/Console.png deleted file mode 100644 index 27529de0bb..0000000000 Binary files a/doc/sphinx/Clusters_from_Scratch/images/Console.png and /dev/null differ diff --git a/doc/sphinx/Clusters_from_Scratch/images/ConsolePrompt.png b/doc/sphinx/Clusters_from_Scratch/images/ConsolePrompt.png new file mode 100644 index 0000000000..606280b967 Binary files /dev/null and b/doc/sphinx/Clusters_from_Scratch/images/ConsolePrompt.png differ diff --git a/doc/sphinx/Clusters_from_Scratch/images/Editing-eth0.png b/doc/sphinx/Clusters_from_Scratch/images/Editing-eth0.png deleted file mode 100644 index d9ba68ebeb..0000000000 Binary files a/doc/sphinx/Clusters_from_Scratch/images/Editing-eth0.png and /dev/null differ diff --git a/doc/sphinx/Clusters_from_Scratch/images/InstallationSummary.png b/doc/sphinx/Clusters_from_Scratch/images/InstallationSummary.png new file mode 100644 index 0000000000..01bf8625a8 Binary files /dev/null and b/doc/sphinx/Clusters_from_Scratch/images/InstallationSummary.png differ diff --git a/doc/sphinx/Clusters_from_Scratch/images/Installer.png b/doc/sphinx/Clusters_from_Scratch/images/Installer.png deleted file mode 100644 index fb35f1c849..0000000000 Binary files a/doc/sphinx/Clusters_from_Scratch/images/Installer.png and /dev/null differ diff --git a/doc/sphinx/Clusters_from_Scratch/images/ManualPartitioning.png b/doc/sphinx/Clusters_from_Scratch/images/ManualPartitioning.png new file mode 100644 index 0000000000..83a8b9485a Binary files /dev/null and b/doc/sphinx/Clusters_from_Scratch/images/ManualPartitioning.png differ diff --git a/doc/sphinx/Clusters_from_Scratch/images/NetworkAndHostName.png b/doc/sphinx/Clusters_from_Scratch/images/NetworkAndHostName.png new file mode 100644 index 0000000000..16245efb69 Binary files /dev/null and b/doc/sphinx/Clusters_from_Scratch/images/NetworkAndHostName.png differ diff --git a/doc/sphinx/Clusters_from_Scratch/images/Partitioning.png b/doc/sphinx/Clusters_from_Scratch/images/Partitioning.png deleted file mode 100644 index e379aa6b01..0000000000 Binary files a/doc/sphinx/Clusters_from_Scratch/images/Partitioning.png and /dev/null differ diff --git a/doc/sphinx/Clusters_from_Scratch/images/RootPassword.png b/doc/sphinx/Clusters_from_Scratch/images/RootPassword.png new file mode 100644 index 0000000000..83ebb5b3eb Binary files /dev/null and b/doc/sphinx/Clusters_from_Scratch/images/RootPassword.png differ diff --git a/doc/sphinx/Clusters_from_Scratch/images/SoftwareSelection.png b/doc/sphinx/Clusters_from_Scratch/images/SoftwareSelection.png new file mode 100644 index 0000000000..26ae1bc038 Binary files /dev/null and b/doc/sphinx/Clusters_from_Scratch/images/SoftwareSelection.png differ diff --git a/doc/sphinx/Clusters_from_Scratch/images/Welcome.png b/doc/sphinx/Clusters_from_Scratch/images/Welcome.png deleted file mode 100644 index f44ba434d3..0000000000 Binary files a/doc/sphinx/Clusters_from_Scratch/images/Welcome.png and /dev/null differ diff --git a/doc/sphinx/Clusters_from_Scratch/images/WelcomeToCentos.png b/doc/sphinx/Clusters_from_Scratch/images/WelcomeToCentos.png new file mode 100644 index 0000000000..ae9879c740 Binary files /dev/null and b/doc/sphinx/Clusters_from_Scratch/images/WelcomeToCentos.png differ diff --git a/doc/sphinx/Clusters_from_Scratch/index.rst b/doc/sphinx/Clusters_from_Scratch/index.rst index 8890c046c0..8ca099c917 100644 --- a/doc/sphinx/Clusters_from_Scratch/index.rst +++ b/doc/sphinx/Clusters_from_Scratch/index.rst @@ -1,52 +1,52 @@ Clusters from Scratch ===================== *Step-by-Step Instructions for Building Your First High-Availability Cluster* Abstract -------- This document provides a step-by-step guide to building a simple high-availability cluster using Pacemaker. The example cluster will use: * |CFS_DISTRO| |CFS_DISTRO_VER| as the host operating system * Corosync to provide messaging and membership services, -* Pacemaker 1.1.18 [#]_ +* Pacemaker 2 [#]_ * DRBD as a cost-effective alternative to shared storage, * GFS2 as the cluster filesystem (in active/active mode) Given the graphical nature of the install process, a number of screenshots are included. However the guide is primarily composed of commands, the reasons for executing them and their expected outputs. Table of Contents ----------------- .. toctree:: :maxdepth: 3 :numbered: intro installation cluster-setup verification fencing active-passive apache shared-storage active-active ap-configuration ap-corosync-conf ap-reading Index ----- * :ref:`genindex` * :ref:`search` .. [#] While this guide is part of the document set for Pacemaker 2.0, it demonstrates the version available in the standard |CFS_DISTRO| repositories diff --git a/doc/sphinx/Clusters_from_Scratch/installation.rst b/doc/sphinx/Clusters_from_Scratch/installation.rst index f5dcc7d1e8..2827cda52a 100644 --- a/doc/sphinx/Clusters_from_Scratch/installation.rst +++ b/doc/sphinx/Clusters_from_Scratch/installation.rst @@ -1,408 +1,436 @@ Installation ------------ Install |CFS_DISTRO| |CFS_DISTRO_VER| ################################################################################################ Boot the Install Image ______________________ -Download the 4GB |CFS_DISTRO| |CFS_DISTRO_VER| `DVD ISO `_. +Download the latest |CFS_DISTRO| |CFS_DISTRO_VER| DVD ISO by navigating to +the `CentOS Mirrors List `_, +selecting a download mirror which is close to you, and finally selecting the +.iso file that has "dvd" in its name. Use the image to boot a virtual machine, or burn it to a DVD or USB drive and boot a physical server from that. After starting the installation, select your language and keyboard layout at the welcome screen. -.. figure:: images/Welcome.png +.. figure:: images/WelcomeToCentos.png :scale: 80% :width: 1024 :height: 800 :align: center :alt: Installation Welcome Screen |CFS_DISTRO| |CFS_DISTRO_VER| Installation Welcome Screen Installation Options ____________________ At this point, you get a chance to tweak the default installation options. -.. figure:: images/Installer.png +.. figure:: images/InstallationSummary.png :scale: 80% :width: 1024 :height: 800 :align: center :alt: Installation Summary Screen |CFS_DISTRO| |CFS_DISTRO_VER| Installation Summary Screen -Ignore the **SOFTWARE SELECTION** section (try saying that 10 times quickly). The -**Infrastructure Server** environment does have add-ons with much of the software -we need, but we will leave it as a **Minimal Install** here, so that we can see -exactly what software is required later. +Click on the **SOFTWARE SELECTION** section (try saying that 10 times quickly). The +default environment, **Server with GUI**, does have add-ons with much of the software +we need, but we will change the environment to a **Minimal Install** here, so that we +can see exactly what software is required later, and press **Done**. + +.. figure:: images/SoftwareSelection.png + :scale: 80% + :width: 1024 + :height: 800 + :align: center + :alt: Software Selection Screen + + |CFS_DISTRO| |CFS_DISTRO_VER| Software Selection Screen Configure Network _________________ In the **NETWORK & HOSTNAME** section: - Edit **Host Name:** as desired. For this example, we will use - **pcmk-1.localdomain**. -- Select your network device, press **Configure...**, and manually assign a fixed - IP address. For this example, we'll use 192.168.122.101 under **IPv4 Settings** - (with an appropriate netmask, gateway and DNS server). + **pcmk-1.localdomain** and then press **Apply**. +- Select your network device, press **Configure...**, and use the **Manual** method to + assign a fixed IP address. For this example, we'll use 192.168.122.101 under + **IPv4 Settings** (with an appropriate netmask, gateway and DNS server). +- Press **Save**. - Flip the switch to turn your network device on, and press **Done**. -.. figure:: images/Editing-eth0.png +.. figure:: images/NetworkAndHostName.png :scale: 80% :width: 1024 :height: 800 :align: center - :alt: Editing eth0 + :alt: Editing network settings |CFS_DISTRO| |CFS_DISTRO_VER| Network Interface Screen .. IMPORTANT:: Do not accept the default network settings. Cluster machines should never obtain an IP address via DHCP, because DHCP's periodic address renewal will interfere with corosync. Configure Disk ______________ By default, the installer's automatic partitioning will use LVM (which allows us to dynamically change the amount of space allocated to a given partition). However, it allocates all free space to the ``/`` (aka. **root**) partition, which cannot be reduced in size later (dynamic increases are fine). In order to follow the DRBD and GFS2 portions of this guide, we need to reserve space on each machine for a replicated volume. Enter the **INSTALLATION DESTINATION** section, ensure the hard drive you want to -install to is selected, select **I will configure partitioning**, and press **Done**. +install to is selected, select **Custom** to be the **Storage Configuration**, and +press **Done**. In the **MANUAL PARTITIONING** screen that comes next, click the option to create mountpoints automatically. Select the ``/`` mountpoint, and reduce the desired -capacity by 1GiB or so. Select **Modify...** by the volume group name, and change +capacity by 3GiB or so. Select **Modify...** by the volume group name, and change the **Size policy:** to **As large as possible**, to make the reclaimed space available inside the LVM volume group. We'll add the additional volume later. -.. figure:: images/Partitioning.png +.. figure:: images/ManualPartitioning.png :scale: 80% :width: 1024 :height: 800 :align: center :alt: Manual Partitioning Screen |CFS_DISTRO| |CFS_DISTRO_VER| Manual Partitioning Screen Press **Done**, then **Accept changes**. Configure Time Synchronization ______________________________ It is highly recommended to enable NTP on your cluster nodes. Doing so ensures all nodes agree on the current time and makes reading log files significantly easier. |CFS_DISTRO| will enable NTP automatically. If you want to change any time-related settings (such as time zone or NTP server), you can do this in the **TIME & DATE** section. +Root Password +______________________________ + +In order to continue to the next step, a **Root Password** must be set. + +.. figure:: images/RootPassword.png + :scale: 80% + :width: 1024 + :height: 800 + :align: center + :alt: Root Password Screen + + |CFS_DISTRO| |CFS_DISTRO_VER| Root Password Screen + +Press **Done** (depending on the password you chose, you may need to do so twice). + Finish Install ______________ -Select **Begin Installation**. Once it completes, set a root password, and reboot -as instructed. For the purposes of this document, it is not necessary to create -any additional users. After the node reboots, you'll see a login prompt on +Select **Begin Installation**. Once it completes, **Reboot System** +as instructed. After the node reboots, you'll see a login prompt on the console. Login using **root** and the password you created earlier. -.. figure:: images/Console.png +.. figure:: images/ConsolePrompt.png :scale: 80% :width: 1024 :height: 768 :align: center :alt: Console Prompt |CFS_DISTRO| |CFS_DISTRO_VER| Console Prompt .. NOTE:: From here on, we're going to be working exclusively from the terminal. Configure the OS ################ Verify Networking _________________ Ensure that the machine has the static IP address you configured earlier. .. code-block:: none - [root@pcmk-1 ~]# ip addr 1: lo: mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 - link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 - inet 127.0.0.1/8 scope host lo - valid_lft forever preferred_lft forever - inet6 ::1/128 scope host - valid_lft forever preferred_lft forever - 2: eth0: mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 - link/ether 52:54:00:8e:eb:41 brd ff:ff:ff:ff:ff:ff - inet 192.168.122.101/24 brd 192.168.122.255 scope global noprefixroute eth0 - valid_lft forever preferred_lft forever - inet6 fe80::e45:c99b:34c0:c657/64 scope link noprefixroute - valid_lft forever preferred_lft forever + link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 + inet 127.0.0.1/8 scope host lo + valid_lft forever preferred_lft forever + inet6 ::1/128 scope host + valid_lft forever preferred_lft forever + 2: enp1s0: mtu 1500 qdisc fq_codel state UP group default qlen 1000 + link/ether 52:54:00:32:cf:a9 brd ff:ff:ff:ff:ff:ff + inet 192.168.122.101/24 brd 192.168.122.255 scope global noprefixroute enp1s0 + valid_lft forever preferred_lft forever + inet6 fe80::c3e1:3ba:959:fa96/64 scope link noprefixroute + valid_lft forever preferred_lft forever .. NOTE:: If you ever need to change the node's IP address from the command line, follow these instructions, replacing **${device}** with the name of your network device: .. code-block:: none [root@pcmk-1 ~]# vi /etc/sysconfig/network-scripts/ifcfg-${device} # manually edit as desired [root@pcmk-1 ~]# nmcli dev disconnect ${device} [root@pcmk-1 ~]# nmcli con reload ${device} [root@pcmk-1 ~]# nmcli con up ${device} This makes **NetworkManager** aware that a change was made on the config file. Next, ensure that the routes are as expected: .. code-block:: none [root@pcmk-1 ~]# ip route - default via 192.168.122.1 dev eth0 proto static metric 100 - 192.168.122.0/24 dev eth0 proto kernel scope link src 192.168.122.101 metric 100 + default via 192.168.122.1 dev enp1s0 proto static metric 100 + 192.168.122.0/24 dev enp1s0 proto kernel scope link src 192.168.122.101 metric 100 If there is no line beginning with **default via**, then you may need to add a line such as ``GATEWAY="192.168.122.1"`` to the device configuration using the same process as described above for changing the IP address. Now, check for connectivity to the outside world. Start small by testing whether we can reach the gateway we configured. .. code-block:: none [root@pcmk-1 ~]# ping -c 1 192.168.122.1 PING 192.168.122.1 (192.168.122.1) 56(84) bytes of data. - 64 bytes from 192.168.122.1: icmp_seq=1 ttl=64 time=0.254 ms - + 64 bytes from 192.168.122.1: icmp_seq=1 ttl=64 time=0.492 ms + --- 192.168.122.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms - rtt min/avg/max/mdev = 0.254/0.254/0.254/0.000 ms + rtt min/avg/max/mdev = 0.492/0.492/0.492/0.000 ms Now try something external; choose a location you know should be available. .. code-block:: none [root@pcmk-1 ~]# ping -c 1 www.clusterlabs.org - PING oss-uk-1.clusterlabs.org (109.74.197.241) 56(84) bytes of data. - 64 bytes from oss-uk-1.clusterlabs.org (109.74.197.241): icmp_seq=1 ttl=49 time=333 ms - - --- oss-uk-1.clusterlabs.org ping statistics --- + PING mx1.clusterlabs.org (95.217.104.78) 56(84) bytes of data. + 64 bytes from mx1.clusterlabs.org (95.217.104.78): icmp_seq=1 ttl=54 time=134 ms + + --- mx1.clusterlabs.org ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms - rtt min/avg/max/mdev = 333.204/333.204/333.204/0.000 ms + rtt min/avg/max/mdev = 133.987/133.987/133.987/0.000 ms Login Remotely ______________ The console isn't a very friendly place to work from, so we will now switch to accessing the machine remotely via SSH where we can use copy and paste, etc. From another host, check whether we can see the new host at all: .. code-block:: none - beekhof@f16 ~ # ping -c 1 192.168.122.101 + [gchin@gchin ~]$ ping -c 1 192.168.122.101 PING 192.168.122.101 (192.168.122.101) 56(84) bytes of data. - 64 bytes from 192.168.122.101: icmp_req=1 ttl=64 time=1.01 ms - + 64 bytes from 192.168.122.101: icmp_seq=1 ttl=64 time=0.344 ms + --- 192.168.122.101 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms - rtt min/avg/max/mdev = 1.012/1.012/1.012/0.000 ms - + rtt min/avg/max/mdev = 0.344/0.344/0.344/0.000 ms + Next, login as root via SSH. .. code-block:: none - beekhof@f16 ~ # ssh -l root 192.168.122.101 + [gchin@gchin ~]$ ssh root@192.168.122.101 The authenticity of host '192.168.122.101 (192.168.122.101)' can't be established. - ECDSA key fingerprint is 6e:b7:8f:e2:4c:94:43:54:a8:53:cc:20:0f:29:a4:e0. - Are you sure you want to continue connecting (yes/no)? yes + ECDSA key fingerprint is SHA256:NBvcRrPDLIt39Rf0Tz4/f2Rd/FA5wUiDOd9bZ9QWWjo. + Are you sure you want to continue connecting (yes/no/[fingerprint])? yes Warning: Permanently added '192.168.122.101' (ECDSA) to the list of known hosts. - root@192.168.122.101's password: - Last login: Tue Aug 11 13:14:39 2015 - [root@pcmk-1 ~]# + root@192.168.122.101's password: + Last login: Tue Jan 10 20:46:30 2021 + [root@pcmk-1 ~]# Apply Updates _____________ Apply any package updates released since your installation image was created: .. code-block:: none [root@pcmk-1 ~]# yum update .. index:: single: node; short name Use Short Node Names ____________________ During installation, we filled in the machine's fully qualified domain name (FQDN), which can be rather long when it appears in cluster logs and status output. See for yourself how the machine identifies itself: .. code-block:: none [root@pcmk-1 ~]# uname -n pcmk-1.localdomain We can use the `hostnamectl` tool to strip off the domain name: .. code-block:: none [root@pcmk-1 ~]# hostnamectl set-hostname $(uname -n | sed s/\\..*//) Now, check that the machine is using the correct name: .. code-block:: none [root@pcmk-1 ~]# uname -n pcmk-1 You may want to reboot to ensure all updates take effect. Repeat for Second Node ###################### Repeat the Installation steps so far, so that you have two nodes ready to have the cluster software installed. For the purposes of this document, the additional node is called pcmk-2 with address 192.168.122.102. Configure Communication Between Nodes ##################################### Configure Host Name Resolution ______________________________ Confirm that you can communicate between the two new nodes: .. code-block:: none [root@pcmk-1 ~]# ping -c 3 192.168.122.102 PING 192.168.122.102 (192.168.122.102) 56(84) bytes of data. - 64 bytes from 192.168.122.102: icmp_seq=1 ttl=64 time=0.343 ms - 64 bytes from 192.168.122.102: icmp_seq=2 ttl=64 time=0.402 ms - 64 bytes from 192.168.122.102: icmp_seq=3 ttl=64 time=0.558 ms - + 64 bytes from 192.168.122.102: icmp_seq=1 ttl=64 time=1.22 ms + 64 bytes from 192.168.122.102: icmp_seq=2 ttl=64 time=0.795 ms + 64 bytes from 192.168.122.102: icmp_seq=3 ttl=64 time=0.751 ms + --- 192.168.122.102 ping statistics --- - 3 packets transmitted, 3 received, 0% packet loss, time 2000ms - rtt min/avg/max/mdev = 0.343/0.434/0.558/0.092 ms + 3 packets transmitted, 3 received, 0% packet loss, time 2054ms + rtt min/avg/max/mdev = 0.751/0.923/1.224/0.214 ms Now we need to make sure we can communicate with the machines by their name. If you have a DNS server, add additional entries for the two machines. Otherwise, you'll need to add the machines to ``/etc/hosts`` on both nodes. Below are the entries for my cluster nodes: .. code-block:: none [root@pcmk-1 ~]# grep pcmk /etc/hosts 192.168.122.101 pcmk-1.clusterlabs.org pcmk-1 192.168.122.102 pcmk-2.clusterlabs.org pcmk-2 We can now verify the setup by again using ping: .. code-block:: none [root@pcmk-1 ~]# ping -c 3 pcmk-2 - PING pcmk-2.clusterlabs.org (192.168.122.101) 56(84) bytes of data. - 64 bytes from pcmk-1.clusterlabs.org (192.168.122.101): icmp_seq=1 ttl=64 time=0.164 ms - 64 bytes from pcmk-1.clusterlabs.org (192.168.122.101): icmp_seq=2 ttl=64 time=0.475 ms - 64 bytes from pcmk-1.clusterlabs.org (192.168.122.101): icmp_seq=3 ttl=64 time=0.186 ms - + PING pcmk-2.clusterlabs.org (192.168.122.102) 56(84) bytes of data. + 64 bytes from pcmk-2.clusterlabs.org (192.168.122.102): icmp_seq=1 ttl=64 time=0.295 ms + 64 bytes from pcmk-2.clusterlabs.org (192.168.122.102): icmp_seq=2 ttl=64 time=0.616 ms + 64 bytes from pcmk-2.clusterlabs.org (192.168.122.102): icmp_seq=3 ttl=64 time=0.809 ms + --- pcmk-2.clusterlabs.org ping statistics --- - 3 packets transmitted, 3 received, 0% packet loss, time 2001ms - rtt min/avg/max/mdev = 0.164/0.275/0.475/0.141 ms - + 3 packets transmitted, 3 received, 0% packet loss, time 2043ms + rtt min/avg/max/mdev = 0.295/0.573/0.809/0.212 ms .. index:: SSH Configure SSH _____________ SSH is a convenient and secure way to copy files and perform commands remotely. For the purposes of this guide, we will create a key without a password (using the -N option) so that we can perform remote actions without being prompted. .. WARNING:: Unprotected SSH keys (those without a password) are not recommended for servers exposed to the outside world. We use them here only to simplify the demo. Create a new key and allow anyone with that key to log in: .. index:: single: SSH; key .Creating and Activating a new SSH Key .. code-block:: none [root@pcmk-1 ~]# ssh-keygen -t dsa -f ~/.ssh/id_dsa -N "" Generating public/private dsa key pair. + Created directory '/root/.ssh'. Your identification has been saved in /root/.ssh/id_dsa. Your public key has been saved in /root/.ssh/id_dsa.pub. The key fingerprint is: - 91:09:5c:82:5a:6a:50:08:4e:b2:0c:62:de:cc:74:44 root@pcmk-1.clusterlabs.org + SHA256:ehR595AVLAVpvFgqYXiayds2qx8emkvnHmfQZMTZ4jM root@pcmk-1 The key's randomart image is: - +--[ DSA 1024]----+ - |==.ooEo.. | - |X O + .o o | - | * A + | - | + . | - | . S | - | | - | | - | | - | | - +-----------------+ + +---[DSA 1024]----+ + | . ..+.=+. | + | . +o+ Bo. | + | . *oo+*+o | + | = .*E..o | + | oS..o . | + | .o+. | + | o.*oo | + | . B.* | + | === | + +----[SHA256]-----+ [root@pcmk-1 ~]# cp ~/.ssh/id_dsa.pub ~/.ssh/authorized_keys Install the key on the other node: .. code-block:: none [root@pcmk-1 ~]# scp -r ~/.ssh pcmk-2: The authenticity of host 'pcmk-2 (192.168.122.102)' can't be established. - ECDSA key fingerprint is SHA256:63xNPkPYq98rYznf3T9QYJAzlaGiAsSgFVNHOZjPWqc. - ECDSA key fingerprint is MD5:d9:bf:6e:32:88:be:47:3d:96:f1:96:27:65:05:0b:c3. - Are you sure you want to continue connecting (yes/no)? yes + ECDSA key fingerprint is SHA256:FQ4sVubTiHdQ6IetbN96fixoTVx/LuQUV8qoyiywnfs. + Are you sure you want to continue connecting (yes/no/[fingerprint])? yes Warning: Permanently added 'pcmk-2,192.168.122.102' (ECDSA) to the list of known hosts. - root@pcmk-2's password: - id_dsa - id_dsa.pub - authorized_keys - known_hosts + root@pcmk-2's password: + id_dsa 100% 1385 1.6MB/s 00:00 + id_dsa.pub 100% 601 1.0MB/s 00:00 + authorized_keys 100% 601 1.3MB/s 00:00 + known_hosts 100% 184 389.2KB/s 00:00 Test that you can now run commands remotely, without being prompted: .. code-block:: none [root@pcmk-1 ~]# ssh pcmk-2 -- uname -n + root@pcmk-2's password: pcmk-2 diff --git a/doc/sphinx/Clusters_from_Scratch/shared-storage.rst b/doc/sphinx/Clusters_from_Scratch/shared-storage.rst index 938b79ec1d..c9973e8372 100644 --- a/doc/sphinx/Clusters_from_Scratch/shared-storage.rst +++ b/doc/sphinx/Clusters_from_Scratch/shared-storage.rst @@ -1,627 +1,613 @@ .. index:: pair: storage; DRBD Replicate Storage Using DRBD ---------------------------- Even if you're serving up static websites, having to manually synchronize the contents of that website to all the machines in the cluster is not ideal. For dynamic websites, such as a wiki, it's not even an option. Not -everyone care afford network-attached storage, but somehow the data needs +everyone can afford network-attached storage, but somehow the data needs to be kept in sync. Enter DRBD, which can be thought of as network-based RAID-1 [#]_. Install the DRBD Packages ######################### DRBD itself is included in the upstream kernel [#]_, but we do need some utilities to use it effectively. CentOS does not ship these utilities, so we need to enable a third-party repository to get them. Supported packages for many OSes are available from DRBD's maker `LINBIT `_, but here we'll use the free `ELRepo `_ repository. On both nodes, import the ELRepo package signing key, and enable the repository: .. code-block:: none # rpm --import https://www.elrepo.org/RPM-GPG-KEY-elrepo.org - # rpm -Uvh http://www.elrepo.org/elrepo-release-7.0-3.el7.elrepo.noarch.rpm - Retrieving http://www.elrepo.org/elrepo-release-7.0-3.el7.elrepo.noarch.rpm + # rpm -Uvh https://www.elrepo.org/elrepo-release-8.el8.elrepo.noarch.rpm + Retrieving https://www.elrepo.org/elrepo-release-8.el8.elrepo.noarch.rpm + Verifying... ################################# [100%] Preparing... ################################# [100%] Updating / installing... - 1:elrepo-release-7.0-3.el7.elrepo ################################# [100%] + 1:elrepo-release-8.2-1.el8.elrepo ################################# [100%] Now, we can install the DRBD kernel module and utilities: .. code-block:: none - # yum install -y kmod-drbd84 drbd84-utils + # yum install -y kmod-drbd90 drbd90-utils DRBD will not be able to run under the default SELinux security policies. If you are familiar with SELinux, you can modify the policies in a more fine-grained manner, but here we will simply exempt DRBD processes from SELinux control: .. code-block:: none + # yum install -y policycoreutils-python-utils # semanage permissive -a drbd_t We will configure DRBD to use port 7789, so allow that port from each host to the other: .. code-block:: none [root@pcmk-1 ~]# firewall-cmd --permanent --add-rich-rule='rule family="ipv4" \ source address="192.168.122.102" port port="7789" protocol="tcp" accept' success [root@pcmk-1 ~]# firewall-cmd --reload success .. code-block:: none [root@pcmk-2 ~]# firewall-cmd --permanent --add-rich-rule='rule family="ipv4" \ source address="192.168.122.101" port port="7789" protocol="tcp" accept' success [root@pcmk-2 ~]# firewall-cmd --reload success .. NOTE:: In this example, we have only two nodes, and all network traffic is on the same LAN. In production, it is recommended to use a dedicated, isolated network for cluster-related traffic, so the firewall configuration would likely be different; one approach would be to add the dedicated network interfaces to the trusted zone. Allocate a Disk Volume for DRBD ############################### DRBD will need its own block device on each node. This can be a physical disk partition or logical volume, of whatever size you need for your data. For this document, we will use a 512MiB logical volume, which is more than sufficient for a single HTML file and (later) GFS2 metadata. .. code-block:: none [root@pcmk-1 ~]# vgdisplay | grep -e Name -e Free - VG Name centos_pcmk-1 - Free PE / Size 255 / 1020.00 MiB - [root@pcmk-1 ~]# lvcreate --name drbd-demo --size 512M centos_pcmk-1 + VG Name cs_pcmk-1 + Free PE / Size 3583 / <14.00 GiB + [root@pcmk-1 ~]# lvcreate --name drbd-demo --size 512M cs_pcmk-1 Logical volume "drbd-demo" created. [root@pcmk-1 ~]# lvs LV VG Attr LSize Pool Origin Data% Meta% Move Log Cpy%Sync Convert drbd-demo centos_pcmk-1 -wi-a----- 512.00m root centos_pcmk-1 -wi-ao---- 3.00g swap centos_pcmk-1 -wi-ao---- 1.00g Repeat for the second node, making sure to use the same size: .. code-block:: none - [root@pcmk-1 ~]# ssh pcmk-2 -- lvcreate --name drbd-demo --size 512M centos_pcmk-2 + [root@pcmk-1 ~]# ssh pcmk-2 -- lvcreate --name drbd-demo --size 512M cs_pcmk-2 Logical volume "drbd-demo" created. Configure DRBD ############## There is no series of commands for building a DRBD configuration, so simply run this on both nodes to use this sample configuration: .. code-block:: none # cat </etc/drbd.d/wwwdata.res resource wwwdata { protocol C; meta-disk internal; device /dev/drbd1; syncer { verify-alg sha1; } net { allow-two-primaries; } on pcmk-1 { - disk /dev/centos_pcmk-1/drbd-demo; + disk /dev/cs_pcmk-1/drbd-demo; address 192.168.122.101:7789; } on pcmk-2 { - disk /dev/centos_pcmk-2/drbd-demo; + disk /dev/cs_pcmk-2/drbd-demo; address 192.168.122.102:7789; } } END .. IMPORTANT:: Edit the file to use the hostnames, IP addresses and logical volume paths of your nodes if they differ from the ones used in this guide. .. NOTE:: Detailed information on the directives used in this configuration (and other alternatives) is available in the `DRBD User's Guide `_. The **allow-two-primaries** option would not normally be used in an active/passive cluster. We are adding it here for the convenience of changing to an active/active cluster later. Initialize DRBD ############### With the configuration in place, we can now get DRBD running. These commands create the local metadata for the DRBD resource, ensure the DRBD kernel module is loaded, and bring up the DRBD resource. Run them on one node: .. code-block:: none [root@pcmk-1 ~]# drbdadm create-md wwwdata - - - - - - - - - - - - - - - - - - - - --== Thank you for participating in the global usage survey ==-- - The server's response is: - - you are the 2147th user to install this version initializing activity log initializing bitmap (16 KB) to all zero Writing meta data... New drbd meta data block successfully created. - success [root@pcmk-1 ~]# modprobe drbd [root@pcmk-1 ~]# drbdadm up wwwdata - - - - - - - - - - - - - - - - - - + + + + + + + + + + + + + + + + + --== Thank you for participating in the global usage survey ==-- The server's response is: - -We can confirm DRBD's status on this node: - + + you are the 801th user to install this version + + We can confirm DRBD's status on this node: + .. code-block:: none - [root@pcmk-1 ~]# cat /proc/drbd - version: 8.4.11-1 (api:1/proto:86-101) - GIT-hash: 66145a308421e9c124ec391a7848ac20203bb03c build by mockbuild@, 2018-04-26 12:10:42 - - 1: cs:WFConnection ro:Secondary/Unknown ds:Inconsistent/DUnknown C r----s - ns:0 nr:0 dw:0 dr:0 al:8 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:524236 + [root@pcmk-1 ~]# drbdadm status + wwwdata role:Secondary + disk:Inconsistent + pcmk-2 connection:Connecting Because we have not yet initialized the data, this node's data is marked as **Inconsistent**. Because we have not yet initialized -the second node, the local state is **WFConnection** (waiting for connection), -and the partner node's status is marked as **Unknown**. +the second node, the pcmk-2 connection is **Connecting** (waiting for connection). Now, repeat the above commands on the second node, starting with creating -wwwdata.res. After giving it time to connect, when we check the status, it -shows: +wwwdata.res. After giving it time to connect, when we check the status of the first +node, it shows: .. code-block:: none - [root@pcmk-2 ~]# cat /proc/drbd - version: 8.4.11-1 (api:1/proto:86-101) - GIT-hash: 66145a308421e9c124ec391a7848ac20203bb03c build by mockbuild@, 2018-04-26 12:10:42 - - 1: cs:Connected ro:Secondary/Secondary ds:Inconsistent/Inconsistent C r----- - ns:0 nr:0 dw:0 dr:0 al:8 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:524236 + [root@pcmk-1 ~]# drbdadm status + wwwdata role:Secondary + disk:Inconsistent + pcmk-2 role:Secondary + peer-disk:Inconsistent -You can see the state has changed to **Connected**, meaning the two DRBD nodes -are communicating properly, and both nodes are in **Secondary** role -with **Inconsistent** data. +You can see that **pcmk-2 connection:Connecting** longer appears in the +output, meaning the two DRBD nodes are communicating properly, and both +nodes are in **Secondary** role with **Inconsistent** data. To make the data consistent, we need to tell DRBD which node should be considered to have the correct data. In this case, since we are creating a new resource, both have garbage, so we'll just pick pcmk-1 and run this command on it: .. code-block:: none [root@pcmk-1 ~]# drbdadm primary --force wwwdata .. NOTE:: If you are using a different version of DRBD, the required syntax may be different. See the documentation for your version for how to perform these commands. -If we check the status immediately, we'll see something like this: +If we check the status of both nodes immediately, we'll see something like this: .. code-block:: none - [root@pcmk-1 ~]# cat /proc/drbd - version: 8.4.11-1 (api:1/proto:86-101) - GIT-hash: 66145a308421e9c124ec391a7848ac20203bb03c build by mockbuild@, 2018-04-26 12:10:42 - - 1: cs:SyncSource ro:Primary/Secondary ds:UpToDate/Inconsistent C r----- - ns:43184 nr:0 dw:0 dr:45312 al:8 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:481052 - [>...................] sync'ed: 8.6% (481052/524236)K - finish: 0:01:51 speed: 4,316 (4,316) K/sec - -We can see that this node has the **Primary** role, the partner node has -the **Secondary** role, this node's data is now considered **UpToDate**, -the partner node's data is still **Inconsistent**, and a progress bar -shows how far along the partner node is in synchronizing the data. + [root@pcmk-1 ~]# drbdadm status + wwwdata role:Primary + disk:UpToDate + pcmk-1 role:Secondary + peer-disk:UpToDate + [root@pcmk-2 ~]# drbdadm status + wwwdata role:Secondary + disk:UpToDate + pcmk-1 role:Primary + peer-disk:Inconsistent + +We can see that the first node has the **Primary** role, its partner node has +the **Secondary** role, the first node's data is now considered **UpToDate**, +the partner node's data is still **Inconsistent**. After a while, the sync should finish, and you'll see something like: .. code-block:: none - [root@pcmk-1 ~]# cat /proc/drbd - version: 8.4.11-1 (api:1/proto:86-101) - GIT-hash: 66145a308421e9c124ec391a7848ac20203bb03c build by mockbuild@, 2018-04-26 12:10:42 - - 1: cs:Connected ro:Primary/Secondary ds:UpToDate/UpToDate C r----- - ns:524236 nr:0 dw:0 dr:526364 al:8 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 + [root@pcmk-1 ~]# drbdadm status + wwwdata role:Primary + disk:UpToDate + pcmk-1 role:Secondary + peer-disk:UpToDate + [root@pcmk-2 ~]# drbdadm status + wwwdata role:Secondary + disk:UpToDate + pcmk-1 role:Primary + peer-disk:UpToDate Both sets of data are now **UpToDate**, and we can proceed to creating and populating a filesystem for our WebSite resource's documents. Populate the DRBD Disk ###################### On the node with the primary role (pcmk-1 in this example), create a filesystem on the DRBD device: .. code-block:: none [root@pcmk-1 ~]# mkfs.xfs /dev/drbd1 meta-data=/dev/drbd1 isize=512 agcount=4, agsize=32765 blks = sectsz=512 attr=2, projid32bit=1 - = crc=1 finobt=0, sparse=0 + = crc=1 finobt=1, sparse=1, rmapbt=0 + = reflink=1 data = bsize=4096 blocks=131059, imaxpct=25 = sunit=0 swidth=0 blks - naming =version 2 bsize=4096 ascii-ci=0 ftype=1 - log =internal log bsize=4096 blocks=855, version=2 + naming =version 2 bsize=4096 ascii-ci=0, ftype=1 + log =internal log bsize=4096 blocks=1368, version=2 = sectsz=512 sunit=0 blks, lazy-count=1 realtime =none extsz=4096 blocks=0, rtextents=0 + Discarding blocks...Done. .. NOTE:: In this example, we create an xfs filesystem with no special options. In a production environment, you should choose a filesystem type and options that are suitable for your application. Mount the newly created filesystem, populate it with our web document, give it the same SELinux policy as the web document root, then unmount it (the cluster will handle mounting and unmounting it later): .. code-block:: none [root@pcmk-1 ~]# mount /dev/drbd1 /mnt [root@pcmk-1 ~]# cat <<-END >/mnt/index.html My Test Site - DRBD END [root@pcmk-1 ~]# chcon -R --reference=/var/www/html /mnt [root@pcmk-1 ~]# umount /dev/drbd1 Configure the Cluster for the DRBD device ######################################### One handy feature ``pcs`` has is the ability to queue up several changes into a file and commit those changes all at once. To do this, start by populating the file with the current raw XML config from the CIB. .. code-block:: none [root@pcmk-1 ~]# pcs cluster cib drbd_cfg Using pcs's ``-f`` option, make changes to the configuration saved in the ``drbd_cfg`` file. These changes will not be seen by the cluster until the ``drbd_cfg`` file is pushed into the live cluster's CIB later. Here, we create a cluster resource for the DRBD device, and an additional *clone* resource to allow the resource to run on both nodes at the same time. .. code-block:: none [root@pcmk-1 ~]# pcs -f drbd_cfg resource create WebData ocf:linbit:drbd \ drbd_resource=wwwdata op monitor interval=60s - [root@pcmk-1 ~]# pcs -f drbd_cfg resource master WebDataClone WebData \ - master-max=1 master-node-max=1 clone-max=2 clone-node-max=1 \ - notify=true - [root@pcmk-1 ~]# pcs -f drbd_cfg resource show - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 - WebSite (ocf::heartbeat:apache): Started pcmk-1 - Master/Slave Set: WebDataClone [WebData] - Stopped: [ pcmk-1 pcmk-2 ] - -.. NOTE:: - - In Fedora 29 and CentOS 8.0, 'master' resources have been renamed to - 'promotable clone' resources and the `pcs` command has been changed - accordingly: - - .. code-block:: none - - [root@pcmk-1 ~]# pcs -f drbd_cfg resource promotable WebData \ - promoted-max=1 promoted-node-max=1 clone-max=2 clone-node-max=1 \ - notify=true - - The new command does not allow to set a custom name for the resulting - promotable resource. ``pcs`` automatically creates a name for the resource in - the form of **-clone**, that is **WebData-clone** in this case. - - To avoid confusion whether the ``pcs resource show`` command displays resources' - status or configuration, the command has been deprecated in Fedora 29 and - CentOS 8.0. Two new commands have been introduced for displaying resources' - status and configuration: ``pcs resource status`` and ``pcs resource config``, - respectively. + [root@pcmk-1 ~]# pcs -f drbd_cfg resource promotable WebData \ + promoted-max=1 promoted-node-max=1 clone-max=2 clone-node-max=1 \ + notify=true + [root@pcmk-1 ~]# pcs resource status + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + * WebSite (ocf::heartbeat:apache): Started pcmk-1 + [root@pcmk-1 ~]# pcs resource config + Resource: ClusterIP (class=ocf provider=heartbeat type=IPaddr2) + Attributes: cidr_netmask=24 ip=192.168.122.120 + Operations: monitor interval=30s (ClusterIP-monitor-interval-30s) + start interval=0s timeout=20s (ClusterIP-start-interval-0s) + stop interval=0s timeout=20s (ClusterIP-stop-interval-0s) + Resource: WebSite (class=ocf provider=heartbeat type=apache) + Attributes: configfile=/etc/httpd/conf/httpd.conf statusurl=http://localhost/server-status + Operations: monitor interval=1min (WebSite-monitor-interval-1min) + start interval=0s timeout=40s (WebSite-start-interval-0s) + stop interval=0s timeout=60s (WebSite-stop-interval-0s) After you are satisfied with all the changes, you can commit them all at once by pushing the drbd_cfg file into the live CIB. .. code-block:: none [root@pcmk-1 ~]# pcs cluster cib-push drbd_cfg --config CIB updated Let's see what the cluster did with the new configuration: .. code-block:: none [root@pcmk-1 ~]# pcs status Cluster name: mycluster - Stack: corosync - Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Mon Sep 10 17:58:07 2018 - Last change: Mon Sep 10 17:57:53 2018 by root via cibadmin on pcmk-1 - - 2 nodes configured - 4 resources configured - - Online: [ pcmk-1 pcmk-2 ] - - Full list of resources: - - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 - WebSite (ocf::heartbeat:apache): Started pcmk-1 - Master/Slave Set: WebDataClone [WebData] - Masters: [ pcmk-1 ] - Slaves: [ pcmk-2 ] - + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-1 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Wed Feb 3 09:04:23 2021 + * Last change: Wed Feb 3 09:04:18 2021 by root via cibadmin on pcmk-1 + * 2 nodes configured + * 4 resource instances configured + + Node List: + * Online: [ pcmk-1 pcmk-2 ] + + Full List of Resources: + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + * WebSite (ocf::heartbeat:apache): Started pcmk-1 + * Clone Set: WebData-clone [WebData] (promotable): + * Masters: [ pcmk-1 ] + * Slaves: [ pcmk-2 ] + Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled -We can see that **WebDataClone** (our DRBD device) is running as master (DRBD's +We can see that **WebData-clone** (our DRBD device) is running as master (DRBD's primary role) on **pcmk-1** and slave (DRBD's secondary role) on **pcmk-2**. .. IMPORTANT:: The resource agent should load the DRBD module when needed if it's not already loaded. If that does not happen, configure your operating system to load the module at boot time. For |CFS_DISTRO| |CFS_DISTRO_VER|, you would run this on both nodes: .. code-block:: none # echo drbd >/etc/modules-load.d/drbd.conf Configure the Cluster for the Filesystem ######################################## Now that we have a working DRBD device, we need to mount its filesystem. In addition to defining the filesystem, we also need to tell the cluster where it can be located (only on the DRBD Primary) and when it is allowed to start (after the Primary was promoted). We are going to take a shortcut when creating the resource this time. Instead of explicitly saying we want the **ocf:heartbeat:Filesystem** script, we are only going to ask for **Filesystem**. We can do this because we know there is only one resource script named **Filesystem** available to pacemaker, and that pcs is smart enough to fill in the **ocf:heartbeat:** portion for us correctly in the configuration. If there were multiple **Filesystem** scripts from different OCF providers, we would need to specify the exact one we wanted. Once again, we will queue our changes to a file and then push the new configuration to the cluster as the final step. .. code-block:: none [root@pcmk-1 ~]# pcs cluster cib fs_cfg [root@pcmk-1 ~]# pcs -f fs_cfg resource create WebFS Filesystem \ device="/dev/drbd1" directory="/var/www/html" fstype="xfs" Assumed agent name 'ocf:heartbeat:Filesystem' (deduced from 'Filesystem') [root@pcmk-1 ~]# pcs -f fs_cfg constraint colocation add \ - WebFS with WebDataClone INFINITY with-rsc-role=Master + WebFS with WebData-clone INFINITY with-rsc-role=Master [root@pcmk-1 ~]# pcs -f fs_cfg constraint order \ - promote WebDataClone then start WebFS - Adding WebDataClone WebFS (kind: Mandatory) (Options: first-action=promote then-action=start) + promote WebData-clone then start WebFS + Adding WebData-clone WebFS (kind: Mandatory) (Options: first-action=promote then-action=start) We also need to tell the cluster that Apache needs to run on the same machine as the filesystem and that it must be active before Apache can start. .. code-block:: none [root@pcmk-1 ~]# pcs -f fs_cfg constraint colocation add WebSite with WebFS INFINITY [root@pcmk-1 ~]# pcs -f fs_cfg constraint order WebFS then WebSite Adding WebFS WebSite (kind: Mandatory) (Options: first-action=start then-action=start) Review the updated configuration. .. code-block:: none [root@pcmk-1 ~]# pcs -f fs_cfg constraint Location Constraints: Resource: WebSite - Enabled on: pcmk-1 (score:50) + Enabled on: + Node: pcmk-1 (score:50) Ordering Constraints: start ClusterIP then start WebSite (kind:Mandatory) - promote WebDataClone then start WebFS (kind:Mandatory) + promote WebData-clone then start WebFS (kind:Mandatory) start WebFS then start WebSite (kind:Mandatory) Colocation Constraints: WebSite with ClusterIP (score:INFINITY) - WebFS with WebDataClone (score:INFINITY) (with-rsc-role:Master) + WebFS with WebData-clone (score:INFINITY) (with-rsc-role:Master) WebSite with WebFS (score:INFINITY) Ticket Constraints: - [root@pcmk-1 ~]# pcs -f fs_cfg resource show - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 - WebSite (ocf::heartbeat:apache): Started pcmk-1 - Master/Slave Set: WebDataClone [WebData] - Masters: [ pcmk-1 ] - Slaves: [ pcmk-2 ] - WebFS (ocf::heartbeat:Filesystem): Stopped + [root@pcmk-1 ~]# pcs resource status + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + * WebSite (ocf::heartbeat:apache): Started pcmk-1 + * Clone Set: WebData-clone [WebData] (promotable): + * Masters: [ pcmk-1 ] + * Slaves: [ pcmk-2 ] + [root@pcmk-1 ~]# pcs resource config + Resource: ClusterIP (class=ocf provider=heartbeat type=IPaddr2) + Attributes: cidr_netmask=24 ip=192.168.122.120 + Operations: monitor interval=30s (ClusterIP-monitor-interval-30s) + start interval=0s timeout=20s (ClusterIP-start-interval-0s) + stop interval=0s timeout=20s (ClusterIP-stop-interval-0s) + Resource: WebSite (class=ocf provider=heartbeat type=apache) + Attributes: configfile=/etc/httpd/conf/httpd.conf statusurl=http://localhost/server-status + Operations: monitor interval=1min (WebSite-monitor-interval-1min) + start interval=0s timeout=40s (WebSite-start-interval-0s) + stop interval=0s timeout=60s (WebSite-stop-interval-0s) + Clone: WebData-clone + Meta Attrs: clone-max=2 clone-node-max=1 notify=true promotable=true promoted-max=1 promoted-node-max=1 + Resource: WebData (class=ocf provider=linbit type=drbd) + Attributes: drbd_resource=wwwdata + Operations: demote interval=0s timeout=90 (WebData-demote-interval-0s) + monitor interval=60s (WebData-monitor-interval-60s) + notify interval=0s timeout=90 (WebData-notify-interval-0s) + promote interval=0s timeout=90 (WebData-promote-interval-0s) + reload interval=0s timeout=30 (WebData-reload-interval-0s) + start interval=0s timeout=240 (WebData-start-interval-0s) + stop interval=0s timeout=100 (WebData-stop-interval-0s) After reviewing the new configuration, upload it and watch the cluster put it into effect. .. code-block:: none [root@pcmk-1 ~]# pcs cluster cib-push fs_cfg --config CIB updated [root@pcmk-1 ~]# pcs status Cluster name: mycluster - Stack: corosync - Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Mon Sep 10 18:02:24 2018 - Last change: Mon Sep 10 18:02:14 2018 by root via cibadmin on pcmk-1 - - 2 nodes configured - 5 resources configured - - Online: [ pcmk-1 pcmk-2 ] - - Full list of resources: - - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 - WebSite (ocf::heartbeat:apache): Started pcmk-1 - Master/Slave Set: WebDataClone [WebData] - Masters: [ pcmk-1 ] - Slaves: [ pcmk-2 ] - WebFS (ocf::heartbeat:Filesystem): Started pcmk-1 - + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-1 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Wed Feb 3 09:17:24 2021 + * Last change: Wed Feb 3 09:17:19 2021 by root via cibadmin on pcmk-1 + * 2 nodes configured + * 5 resource instances configured + + Node List: + * Online: [ pcmk-1 pcmk-2 ] + + Full List of Resources: + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + * WebSite (ocf::heartbeat:apache): Started pcmk-1 + * Clone Set: WebData-clone [WebData] (promotable): + * Masters: [ pcmk-1 ] + * Slaves: [ pcmk-2 ] + * WebFS (ocf::heartbeat:Filesystem): Started pcmk-1 + Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled Test Cluster Failover ##################### Previously, we used ``pcs cluster stop pcmk-1`` to stop all cluster services on **pcmk-1**, failing over the cluster resources, but there is another way to safely simulate node failure. We can put the node into *standby mode*. Nodes in this state continue to run corosync and pacemaker but are not allowed to run resources. Any resources found active there will be moved elsewhere. This feature can be particularly useful when performing system administration tasks such as updating packages used by cluster resources. Put the active node into standby mode, and observe the cluster move all the resources to the other node. The node's status will change to indicate that it can no longer host resources, and eventually all the resources will move. .. code-block:: none - [root@pcmk-1 ~]# pcs cluster standby pcmk-1 + [root@pcmk-1 ~]# pcs node standby pcmk-1 [root@pcmk-1 ~]# pcs status Cluster name: mycluster - Stack: corosync - Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Mon Sep 10 18:04:22 2018 - Last change: Mon Sep 10 18:03:43 2018 by root via cibadmin on pcmk-1 - - 2 nodes configured - 5 resources configured - - Node pcmk-1: standby - Online: [ pcmk-2 ] - - Full list of resources: - - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 - WebSite (ocf::heartbeat:apache): Started pcmk-2 - Master/Slave Set: WebDataClone [WebData] - Masters: [ pcmk-2 ] - Stopped: [ pcmk-1 ] - WebFS (ocf::heartbeat:Filesystem): Started pcmk-2 - + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-1 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Wed Feb 3 09:18:45 2021 + * Last change: Wed Feb 3 09:18:35 2021 by root via cibadmin on pcmk-1 + * 2 nodes configured + * 5 resource instances configured + + Node List: + * Node pcmk-1: standby + * Online: [ pcmk-2 ] + + Full List of Resources: + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + * WebSite (ocf::heartbeat:apache): Started pcmk-2 + * Clone Set: WebData-clone [WebData] (promotable): + * Masters: [ pcmk-2 ] + * Stopped: [ pcmk-1 ] + * WebFS (ocf::heartbeat:Filesystem): Started pcmk-2 + Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled Once we've done everything we needed to on pcmk-1 (in this case nothing, we just wanted to see the resources move), we can allow the node to be a full cluster member again. .. code-block:: none - [root@pcmk-1 ~]# pcs cluster unstandby pcmk-1 + [root@pcmk-1 ~]# pcs node unstandby pcmk-1 [root@pcmk-1 ~]# pcs status Cluster name: mycluster - Stack: corosync - Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Mon Sep 10 18:05:22 2018 - Last change: Mon Sep 10 18:05:21 2018 by root via cibadmin on pcmk-1 - - 2 nodes configured - 5 resources configured - - Online: [ pcmk-1 pcmk-2 ] - - Full list of resources: - - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 - WebSite (ocf::heartbeat:apache): Started pcmk-2 - Master/Slave Set: WebDataClone [WebData] - Masters: [ pcmk-2 ] - Slaves: [ pcmk-1 ] - WebFS (ocf::heartbeat:Filesystem): Started pcmk-2 - + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-1 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Wed Feb 3 09:19:47 2021 + * Last change: Wed Feb 3 09:19:29 2021 by root via cibadmin on pcmk-1 + * 2 nodes configured + * 5 resource instances configured + + Node List: + * Online: [ pcmk-1 pcmk-2 ] + + Full List of Resources: + * ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + * WebSite (ocf::heartbeat:apache): Started pcmk-1 + * Clone Set: WebData-clone [WebData] (promotable): + * Masters: [ pcmk-1 ] + * Slaves: [ pcmk-2 ] + * WebFS (ocf::heartbeat:Filesystem): Started pcmk-1 + Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled Notice that **pcmk-1** is back to the **Online** state, and that the cluster resources stay where they are due to our resource stickiness settings configured earlier. -.. NOTE:: - - Since Fedora 29 and CentOS 8.0, the commands for controlling standby mode are - ``pcs node standby`` and ``pcs node unstandby``. - .. [#] See http://www.drbd.org for details. .. [#] Since version 2.6.33 diff --git a/doc/sphinx/Clusters_from_Scratch/verification.rst b/doc/sphinx/Clusters_from_Scratch/verification.rst index 224ce3e269..9d647f81a0 100644 --- a/doc/sphinx/Clusters_from_Scratch/verification.rst +++ b/doc/sphinx/Clusters_from_Scratch/verification.rst @@ -1,211 +1,215 @@ Start and Verify Cluster ------------------------ Start the Cluster ################# Now that corosync is configured, it is time to start the cluster. The command below will start corosync and pacemaker on both nodes in the cluster. If you are issuing the start command from a different -node than the one you ran the ``pcs cluster auth`` command on earlier, you +node than the one you ran the ``pcs host auth`` command on earlier, you must authenticate on the current node you are logged into before you will be allowed to start the cluster. .. code-block:: none [root@pcmk-1 ~]# pcs cluster start --all pcmk-1: Starting Cluster... pcmk-2: Starting Cluster... .. NOTE:: An alternative to using the ``pcs cluster start --all`` command is to issue either of the below command sequences on each node in the cluster separately: .. code-block:: none # pcs cluster start Starting Cluster... or .. code-block:: none # systemctl start corosync.service # systemctl start pacemaker.service .. IMPORTANT:: In this example, we are not enabling the corosync and pacemaker services to start at boot. If a cluster node fails or is rebooted, you will need to run ``pcs cluster start `` (or ``--all``) to start the cluster on it. While you could enable the services to start at boot, requiring a manual start of cluster services gives you the opportunity to do a post-mortem investigation of a node failure before returning it to the cluster. Verify Corosync Installation ############################ First, use ``corosync-cfgtool`` to check whether cluster communication is happy: .. code-block:: none [root@pcmk-1 ~]# corosync-cfgtool -s - Printing ring status. + Printing link status. Local node ID 1 - RING ID 0 - id = 192.168.122.101 - status = ring 0 active with no faults + LINK ID 0 + addr = 192.168.122.101 + status: + nodeid 1: localhost + nodeid 2: connected We can see here that everything appears normal with our fixed IP -address (not a 127.0.0.x loopback address) listed as the **id**, and **no -faults** for the status. +address (not a 127.0.0.x loopback address) listed as the **addr**, and **localhost** and **connected** for the statuses of nodeid 1 and nodeid 2, respectively. If you see something different, you might want to start by checking the node's network, firewall and SELinux configurations. Next, check the membership and quorum APIs: .. code-block:: none [root@pcmk-1 ~]# corosync-cmapctl | grep members - runtime.totem.pg.mrp.srp.members.1.config_version (u64) = 0 - runtime.totem.pg.mrp.srp.members.1.ip (str) = r(0) ip(192.168.122.101) - runtime.totem.pg.mrp.srp.members.1.join_count (u32) = 1 - runtime.totem.pg.mrp.srp.members.1.status (str) = joined - runtime.totem.pg.mrp.srp.members.2.config_version (u64) = 0 - runtime.totem.pg.mrp.srp.members.2.ip (str) = r(0) ip(192.168.122.102) - runtime.totem.pg.mrp.srp.members.2.join_count (u32) = 1 - runtime.totem.pg.mrp.srp.members.2.status (str) = joined - + runtime.members.1.config_version (u64) = 0 + runtime.members.1.ip (str) = r(0) ip(192.168.122.101) + runtime.members.1.join_count (u32) = 1 + runtime.members.1.status (str) = joined + runtime.members.2.config_version (u64) = 0 + runtime.members.2.ip (str) = r(0) ip(192.168.122.102) + runtime.members.2.join_count (u32) = 1 + runtime.members.2.status (str) = joined [root@pcmk-1 ~]# pcs status corosync Membership information - \---------------------- + ---------------------- Nodeid Votes Name 1 1 pcmk-1 (local) 2 1 pcmk-2 You should see both nodes have joined the cluster. Verify Pacemaker Installation ############################# Now that we have confirmed that Corosync is functional, we can check the rest of the stack. Pacemaker has already been started, so verify the necessary processes are running: .. code-block:: none [root@pcmk-1 ~]# ps axf PID TTY STAT TIME COMMAND 2 ? S 0:00 [kthreadd] ...lots of processes... - 11635 ? SLsl 0:03 corosync - 11642 ? Ss 0:00 /usr/sbin/pacemakerd -f - 11643 ? Ss 0:00 \_ /usr/libexec/pacemaker/cib - 11644 ? Ss 0:00 \_ /usr/libexec/pacemaker/stonithd - 11645 ? Ss 0:00 \_ /usr/libexec/pacemaker/lrmd - 11646 ? Ss 0:00 \_ /usr/libexec/pacemaker/attrd - 11647 ? Ss 0:00 \_ /usr/libexec/pacemaker/pengine - 11648 ? Ss 0:00 \_ /usr/libexec/pacemaker/crmd + 17121 ? SLsl 0:01 /usr/sbin/corosync -f + 17133 ? Ss 0:00 /usr/sbin/pacemakerd -f + 17134 ? Ss 0:00 \_ /usr/libexec/pacemaker/pacemaker-based + 17135 ? Ss 0:00 \_ /usr/libexec/pacemaker/pacemaker-fenced + 17136 ? Ss 0:00 \_ /usr/libexec/pacemaker/pacemaker-execd + 17137 ? Ss 0:00 \_ /usr/libexec/pacemaker/pacemaker-attrd + 17138 ? Ss 0:00 \_ /usr/libexec/pacemaker/pacemaker-schedulerd + 17139 ? Ss 0:00 \_ /usr/libexec/pacemaker/pacemaker-controld If that looks OK, check the ``pcs status`` output: .. code-block:: none [root@pcmk-1 ~]# pcs status Cluster name: mycluster - WARNING: no stonith devices and stonith-enabled is not false - Stack: corosync - Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum - Last updated: Mon Sep 10 16:37:34 2018 - Last change: Mon Sep 10 16:30:53 2018 by hacluster via crmd on pcmk-2 - - 2 nodes configured - 0 resources configured - - Online: [ pcmk-1 pcmk-2 ] - - No resources - + + WARNINGS: + No stonith devices and stonith-enabled is not false + + Cluster Summary: + * Stack: corosync + * Current DC: pcmk-2 (version 2.0.5-4.el8-ba59be7122) - partition with quorum + * Last updated: Wed Jan 20 07:54:02 2021 + * Last change: Wed Jan 20 07:48:25 2021 by hacluster via crmd on pcmk-2 + * 2 nodes configured + * 0 resource instances configured + + Node List: + * Online: [ pcmk-1 pcmk-2 ] + + Full List of Resources: + * No resources Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled Finally, ensure there are no start-up errors from corosync or pacemaker (aside from messages relating to not having STONITH configured, which are OK at this point): .. code-block:: none [root@pcmk-1 ~]# journalctl -b | grep -i error .. NOTE:: Other operating systems may report startup errors in other locations, for example ``/var/log/messages``. Repeat these checks on the other node. The results should be the same. Explore the Existing Configuration ################################## For those who are not of afraid of XML, you can see the raw cluster configuration and status by using the ``pcs cluster cib`` command. .. topic:: The last XML you'll see in this document .. code-block:: none [root@pcmk-1 ~]# pcs cluster cib .. code-block:: xml - + - + - - + + - - + + Before we make any changes, it's a good idea to check the validity of the configuration. .. code-block:: none [root@pcmk-1 ~]# crm_verify -L -V error: unpack_resources: Resource start-up disabled since no STONITH resources have been defined error: unpack_resources: Either configure some or disable STONITH with the stonith-enabled option error: unpack_resources: NOTE: Clusters with shared data need STONITH to ensure data integrity Errors found during check: config not valid As you can see, the tool has found some errors. The cluster will not start any resources until we configure STONITH. diff --git a/doc/sphinx/conf.py.in b/doc/sphinx/conf.py.in index 04924e1d27..0c2615a1cb 100644 --- a/doc/sphinx/conf.py.in +++ b/doc/sphinx/conf.py.in @@ -1,314 +1,314 @@ """ Sphinx configuration for Pacemaker documentation """ __copyright__ = "Copyright 2020 the Pacemaker project contributors" __license__ = "GNU General Public License version 2 or later (GPLv2+) WITHOUT ANY WARRANTY" # This file is execfile()d with the current directory set to its containing dir. # # Note that not all possible configuration values are present in this # autogenerated file. # # All configuration values have a default; values that are commented out # serve to show the default. import datetime import os import sys # Variables that can be used later in this file authors = "the Pacemaker project contributors" year = datetime.datetime.now().year doc_license = "Creative Commons Attribution-ShareAlike International Public License" doc_license += " version 4.0 or later (CC-BY-SA v4.0+)" # rST markup to insert at beginning of every document; mainly used for # # .. || replace:: # # where occurrences of || in the rST will be substituted with rst_prolog=""" -.. |CFS_DISTRO| replace:: CentOS -.. |CFS_DISTRO_VER| replace:: 7.5 +.. |CFS_DISTRO| replace:: CentOS Stream +.. |CFS_DISTRO_VER| replace:: 8 .. |REMOTE_DISTRO| replace:: CentOS .. |REMOTE_DISTRO_VER| replace:: 7.4 """ # If extensions (or modules to document with autodoc) are in another directory, # add these directories to sys.path here. If the directory is relative to the # documentation root, use os.path.abspath to make it absolute, like shown here. #sys.path.insert(0, os.path.abspath('.')) # -- General configuration ----------------------------------------------------- # If your documentation needs a minimal Sphinx version, state it here. needs_sphinx = '1.0' # Add any Sphinx extension module names here, as strings. They can be extensions # coming with Sphinx (named 'sphinx.ext.*') or your custom ones. extensions = [] # Add any paths that contain templates here, relative to this directory. templates_path = ['_templates'] # The suffix of source filenames. source_suffix = '.rst' # The encoding of source files. #source_encoding = 'utf-8-sig' # The master toctree document. master_doc = 'index' # General information about the project. project = '%BOOK_ID%' copyright = "2009-%s %s. Released under the terms of the %s" % (year, authors, doc_license) # The version info for the project you're documenting, acts as replacement for # |version| and |release|, also used in various other places throughout the # built documents. # # The full version, including alpha/beta/rc tags. release = '%VERSION%' # The short X.Y version. version = release.rsplit('.', 1)[0] # The language for content autogenerated by Sphinx. Refer to documentation # for a list of supported languages. #language = None # There are two options for replacing |today|: either, you set today to some # non-false value, then it is used: #today = '' # Else, today_fmt is used as the format for a strftime call. #today_fmt = '%B %d, %Y' # List of patterns, relative to source directory, that match files and # directories to ignore when looking for source files. exclude_patterns = ['_build'] # The reST default role (used for this markup: `text`) to use for all documents. #default_role = None # If true, '()' will be appended to :func: etc. cross-reference text. #add_function_parentheses = True # If true, the current module name will be prepended to all description # unit titles (such as .. function::). #add_module_names = True # If true, sectionauthor and moduleauthor directives will be shown in the # output. They are ignored by default. #show_authors = False # The name of the Pygments (syntax highlighting) style to use. pygments_style = 'vs' # A list of ignored prefixes for module index sorting. #modindex_common_prefix = [] # -- Options for HTML output --------------------------------------------------- # The theme to use for HTML and HTML Help pages. See the documentation for # a list of builtin themes. html_theme = 'pyramid' # Theme options are theme-specific and customize the look and feel of a theme # further. For a list of options available for each theme, see the # documentation. #html_theme_options = {} # Add any paths that contain custom themes here, relative to this directory. #html_theme_path = [] html_style = 'pacemaker.css' # The name for this set of Sphinx documents. If None, it defaults to # " v documentation". html_title = "%BOOK_TITLE%" # A shorter title for the navigation bar. Default is the same as html_title. #html_short_title = None # The name of an image file (relative to this directory) to place at the top # of the sidebar. #html_logo = None # The name of an image file (within the static path) to use as favicon of the # docs. This file should be a Windows icon file (.ico) being 16x16 or 32x32 # pixels large. #html_favicon = None # Add any paths that contain custom static files (such as style sheets) here, # relative to this directory. They are copied after the builtin static files, # so a file named "default.css" will overwrite the builtin "default.css". html_static_path = [ '%SRC_DIR%/_static' ] # If not '', a 'Last updated on:' timestamp is inserted at every page bottom, # using the given strftime format. #html_last_updated_fmt = '%b %d, %Y' # If true, SmartyPants will be used to convert quotes and dashes to # typographically correct entities. #html_use_smartypants = True # Custom sidebar templates, maps document names to template names. #html_sidebars = {} # Additional templates that should be rendered to pages, maps page names to # template names. #html_additional_pages = {} # If false, no module index is generated. #html_domain_indices = True # If false, no index is generated. #html_use_index = True # If true, the index is split into individual pages for each letter. #html_split_index = False # If true, links to the reST sources are added to the pages. #html_show_sourcelink = True # If true, "Created using Sphinx" is shown in the HTML footer. Default is True. #html_show_sphinx = True # If true, "(C) Copyright ..." is shown in the HTML footer. Default is True. #html_show_copyright = True # If true, an OpenSearch description file will be output, and all pages will # contain a tag referring to it. The value of this option must be the # base URL from which the finished HTML is served. #html_use_opensearch = '' # This is the file name suffix for HTML files (e.g. ".xhtml"). #html_file_suffix = None # Output file base name for HTML help builder. htmlhelp_basename = 'Pacemakerdoc' # -- Options for LaTeX output -------------------------------------------------- latex_elements = { # The paper size ('letterpaper' or 'a4paper'). #'papersize': 'letterpaper', # The font size ('10pt', '11pt' or '12pt'). #'pointsize': '10pt', # Additional stuff for the LaTeX preamble. #'preamble': '', } # Grouping the document tree into LaTeX files. List of tuples # (source start file, target name, title, author, documentclass [howto/manual]). latex_documents = [ ('index', '%BOOK_ID%.tex', '%BOOK_TITLE%', authors, 'manual'), ] # The name of an image file (relative to this directory) to place at the top of # the title page. #latex_logo = None # For "manual" documents, if this is true, then toplevel headings are parts, # not chapters. #latex_use_parts = False # If true, show page references after internal links. #latex_show_pagerefs = False # If true, show URL addresses after external links. #latex_show_urls = False # Documents to append as an appendix to all manuals. #latex_appendices = [] # If false, no module index is generated. #latex_domain_indices = True # -- Options for manual page output -------------------------------------------- # One entry per manual page. List of tuples # (source start file, name, description, authors, manual section). man_pages = [ ('index', '%BOOK_ID%', 'Part of the Pacemaker documentation set', [authors], 8) ] # If true, show URL addresses after external links. #man_show_urls = False # -- Options for Texinfo output ------------------------------------------------ # Grouping the document tree into Texinfo files. List of tuples # (source start file, target name, title, author, # dir menu entry, description, category) texinfo_documents = [ ('index', '%BOOK_ID%', '%BOOK_TITLE%', authors, '%BOOK_TITLE%', 'Pacemaker is an advanced, scalable high-availability cluster resource manager.', 'Miscellaneous'), ] # Documents to append as an appendix to all manuals. #texinfo_appendices = [] # If false, no module index is generated. #texinfo_domain_indices = True # How to display URL addresses: 'footnote', 'no', or 'inline'. #texinfo_show_urls = 'footnote' # -- Options for Epub output --------------------------------------------------- # Bibliographic Dublin Core info. epub_title = '%BOOK_TITLE%' epub_author = authors epub_publisher = 'ClusterLabs.org' epub_copyright = copyright # The language of the text. It defaults to the language option # or en if the language is not set. #epub_language = '' # The scheme of the identifier. Typical schemes are ISBN or URL. epub_scheme = 'URL' # The unique identifier of the text. This can be a ISBN number # or the project homepage. epub_identifier = 'http://www.clusterlabs.org/pacemaker/doc/2.0/%BOOK_ID%/epub/%BOOK_ID%.epub' # A unique identification for the text. epub_uid = 'ClusterLabs.org-Pacemaker-%BOOK_ID%' # A tuple containing the cover image and cover page html template filenames. #epub_cover = () # HTML files that should be inserted before the pages created by sphinx. # The format is a list of tuples containing the path and title. #epub_pre_files = [] # HTML files that should be inserted after the pages created by sphinx. # The format is a list of tuples containing the path and title. #epub_post_files = [] # A list of files that should not be packed into the epub file. epub_exclude_files = [ '_static/doctools.js', '_static/jquery.js', '_static/searchtools.js', '_static/underscore.js', '_static/basic.css', '_static/websupport.js', 'search.html', ] # The depth of the table of contents in toc.ncx. #epub_tocdepth = 3 # Allow duplicate toc entries. #epub_tocdup = True