diff --git a/doc/Clusters_from_Scratch/en-US/Ap-Configuration.txt b/doc/Clusters_from_Scratch/en-US/Ap-Configuration.txt index 04d57cd4d1..9c15be4af8 100644 --- a/doc/Clusters_from_Scratch/en-US/Ap-Configuration.txt +++ b/doc/Clusters_from_Scratch/en-US/Ap-Configuration.txt @@ -1,451 +1,388 @@ :compat-mode: legacy [appendix] == Configuration Recap == === Final Cluster Configuration === ---- [root@pcmk-1 ~]# pcs resource Master/Slave Set: WebDataClone [WebData] Masters: [ pcmk-1 pcmk-2 ] Clone Set: dlm-clone [dlm] Started: [ pcmk-1 pcmk-2 ] Clone Set: ClusterIP-clone [ClusterIP] (unique) - ClusterIP:0 (ocf::heartbeat:IPaddr2): Started - ClusterIP:1 (ocf::heartbeat:IPaddr2): Started + ClusterIP:0 (ocf::heartbeat:IPaddr2): Started pcmk-2 + ClusterIP:1 (ocf::heartbeat:IPaddr2): Started pcmk-1 Clone Set: WebFS-clone [WebFS] Started: [ pcmk-1 pcmk-2 ] Clone Set: WebSite-clone [WebSite] Started: [ pcmk-1 pcmk-2 ] ---- ---- [root@pcmk-1 ~]# pcs resource op defaults timeout: 240s ---- ---- [root@pcmk-1 ~]# pcs stonith - impi-fencing (stonith:fence_ipmilan) Started + impi-fencing (stonith:fence_ipmilan): Started pcmk-1 ---- ---- [root@pcmk-1 ~]# pcs constraint Location Constraints: Ordering Constraints: start ClusterIP-clone then start WebSite-clone (kind:Mandatory) promote WebDataClone then start WebFS-clone (kind:Mandatory) start WebFS-clone then start WebSite-clone (kind:Mandatory) start dlm-clone then start WebFS-clone (kind:Mandatory) Colocation Constraints: WebSite-clone with ClusterIP-clone (score:INFINITY) WebFS-clone with WebDataClone (score:INFINITY) (with-rsc-role:Master) WebSite-clone with WebFS-clone (score:INFINITY) WebFS-clone with dlm-clone (score:INFINITY) Ticket Constraints: ---- ---- [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-1 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 12:05:37 2018 -Last change: Fri Jan 12 11:49:29 2018 +Current DC: pcmk-1 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Tue Sep 11 10:41:53 2018 +Last change: Tue Sep 11 10:40:16 2018 by root via cibadmin on pcmk-1 2 nodes configured 11 resources configured Online: [ pcmk-1 pcmk-2 ] Full list of resources: - impi-fencing (stonith:fence_ipmilan): Started pcmk-1 + ipmi-fencing (stonith:fence_ipmilan): Started pcmk-1 Master/Slave Set: WebDataClone [WebData] Masters: [ pcmk-1 pcmk-2 ] Clone Set: dlm-clone [dlm] Started: [ pcmk-1 pcmk-2 ] Clone Set: ClusterIP-clone [ClusterIP] (unique) - ClusterIP:0 (ocf::heartbeat:IPaddr2): Started pcmk-2 - ClusterIP:1 (ocf::heartbeat:IPaddr2): Started pcmk-1 + ClusterIP:0 (ocf::heartbeat:IPaddr2): Started pcmk-2 + ClusterIP:1 (ocf::heartbeat:IPaddr2): Started pcmk-1 Clone Set: WebFS-clone [WebFS] Started: [ pcmk-1 pcmk-2 ] Clone Set: WebSite-clone [WebSite] Started: [ pcmk-1 pcmk-2 ] Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ---- ---- -[root@pcmk-1 ~]# pcs cluster cib +[root@pcmk-1 ~]# pcs cluster cib --config ---- [source,XML] ---- - - - - - - - - - - - - - - - - - - - - - - - - - - + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + - + + + + + + + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - + + + + + + - - - - + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - + + + + + + + - - - - - - - - + + + + + + + + + + + + + - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - + + + + + + + + + + + + + + + + + + + + + + + + + + + + + + ---- === Node List === ---- [root@pcmk-1 ~]# pcs status nodes Pacemaker Nodes: - Online: pcmk-1 pcmk-2 - Standby: - Offline: + Online: pcmk-1 pcmk-2 + Standby: + Maintenance: + Offline: +Pacemaker Remote Nodes: + Online: + Standby: + Maintenance: + Offline: ---- === Cluster Options === ---- [root@pcmk-1 ~]# pcs property Cluster Properties: cluster-infrastructure: corosync cluster-name: mycluster - dc-version: 1.1.16-12.el7_4.5-94ff4df + dc-version: 1.1.18-11.el7_5.3-2b07d5c5a9 have-watchdog: false - last-lrm-refresh: 1439569053 + last-lrm-refresh: 1536679009 stonith-enabled: true ---- The output shows state information automatically obtained about the cluster, including: * *cluster-infrastructure* - the cluster communications layer in use * *cluster-name* - the cluster name chosen by the administrator when the cluster was created -* *dc-version* - the version (including upstream source-code hash) of Pacemaker used on the Designated Controller +* *dc-version* - the version (including upstream source-code hash) of Pacemaker + used on the Designated Controller, which is the node elected to determine what + actions are needed when events occur The output also shows options set by the administrator that control the way the cluster operates, including: * *stonith-enabled=true* - whether the cluster is allowed to use STONITH resources === Resources === ==== Default Options ==== ---- [root@pcmk-1 ~]# pcs resource defaults resource-stickiness: 100 ---- This shows cluster option defaults that apply to every resource that does not explicitly set the option itself. Above: * *resource-stickiness* - Specify the aversion to moving healthy resources to other machines ==== Fencing ==== ---- [root@pcmk-1 ~]# pcs stonith show - ipmi-fencing (stonith:fence_ipmilan) Started + ipmi-fencing (stonith:fence_ipmilan): Started pcmk-1 [root@pcmk-1 ~]# pcs stonith show ipmi-fencing Resource: ipmi-fencing (class=stonith type=fence_ipmilan) Attributes: ipaddr="10.0.0.1" login="testuser" passwd="acd123" pcmk_host_list="pcmk-1 pcmk-2" Operations: monitor interval=60s (fence-monitor-interval-60s) ---- ==== Service Address ==== Users of the services provided by the cluster require an unchanging address with which to access it. Additionally, we cloned the address so it will be active on both nodes. An iptables rule (created as part of the resource agent) is used to ensure that each request only gets processed by one of the two clone instances. The additional meta options tell the cluster that we want two instances of the clone (one "request bucket" for each node) and that if one node fails, then the remaining node should hold both. ---- [root@pcmk-1 ~]# pcs resource show ClusterIP-clone Clone: ClusterIP-clone Meta Attrs: clone-max=2 clone-node-max=2 globally-unique=true Resource: ClusterIP (class=ocf provider=heartbeat type=IPaddr2) - Attributes: ip=192.168.122.120 cidr_netmask=32 clusterip_hash=sourceip - Operations: start interval=0s timeout=20s (ClusterIP-start-timeout-20s) - stop interval=0s timeout=20s (ClusterIP-stop-timeout-20s) - monitor interval=30s (ClusterIP-monitor-interval-30s) + Attributes: cidr_netmask=32 ip=192.168.122.120 clusterip_hash=sourceip + Meta Attrs: resource-stickiness=0 + Operations: monitor interval=30s (ClusterIP-monitor-interval-30s) + start interval=0s timeout=20s (ClusterIP-start-interval-0s) + stop interval=0s timeout=20s (ClusterIP-stop-interval-0s) ---- ==== DRBD - Shared Storage ==== Here, we define the DRBD service and specify which DRBD resource (from -/etc/drbd.d/*.res) it should manage. We make it a promotable clone resource and, in +/etc/drbd.d/*.res) it should manage. We make it a master clone resource and, in order to have an active/active setup, allow both instances to be promoted to master at the same time. We also set the notify option so that the cluster will tell DRBD agent when its peer changes state. ---- [root@pcmk-1 ~]# pcs resource show WebDataClone Master: WebDataClone - Meta Attrs: master-max=2 master-node-max=1 clone-max=2 clone-node-max=1 notify=true + Meta Attrs: master-node-max=1 clone-max=2 notify=true master-max=2 clone-node-max=1 Resource: WebData (class=ocf provider=linbit type=drbd) - Attributes: drbd_resource=wwwdata - Operations: start interval=0s timeout=240 (WebData-start-timeout-240) - promote interval=0s timeout=90 (WebData-promote-timeout-90) - demote interval=0s timeout=90 (WebData-demote-timeout-90) - stop interval=0s timeout=100 (WebData-stop-timeout-100) + Attributes: drbd_resource=wwwdata + Operations: demote interval=0s timeout=90 (WebData-demote-interval-0s) monitor interval=60s (WebData-monitor-interval-60s) + notify interval=0s timeout=90 (WebData-notify-interval-0s) + promote interval=0s timeout=90 (WebData-promote-interval-0s) + reload interval=0s timeout=30 (WebData-reload-interval-0s) + start interval=0s timeout=240 (WebData-start-interval-0s) + stop interval=0s timeout=100 (WebData-stop-interval-0s) [root@pcmk-1 ~]# pcs constraint ref WebDataClone Resource: WebDataClone colocation-WebFS-WebDataClone-INFINITY order-WebDataClone-WebFS-mandatory ---- ==== Cluster Filesystem ==== The cluster filesystem ensures that files are read and written correctly. We need to specify the block device (provided by DRBD), where we want it mounted and that we are using GFS2. Again, it is a clone because it is intended to be active on both nodes. The additional constraints ensure that it can only be started on nodes with active DLM and DRBD instances. ---- [root@pcmk-1 ~]# pcs resource show WebFS-clone Clone: WebFS-clone Resource: WebFS (class=ocf provider=heartbeat type=Filesystem) - Attributes: device=/dev/drbd1 directory=/var/www/html fstype=gfs2 - Operations: start interval=0s timeout=60 (WebFS-start-timeout-60) - stop interval=0s timeout=60 (WebFS-stop-timeout-60) - monitor interval=20 timeout=40 (WebFS-monitor-interval-20) + Attributes: device=/dev/drbd1 directory=/var/www/html fstype=gfs2 + Operations: monitor interval=20 timeout=40 (WebFS-monitor-interval-20) + notify interval=0s timeout=60 (WebFS-notify-interval-0s) + start interval=0s timeout=60 (WebFS-start-interval-0s) + stop interval=0s timeout=60 (WebFS-stop-interval-0s) [root@pcmk-1 ~]# pcs constraint ref WebFS-clone Resource: WebFS-clone colocation-WebFS-WebDataClone-INFINITY colocation-WebSite-WebFS-INFINITY - colocation-WebFS-clone-dlm-clone-INFINITY + colocation-WebFS-dlm-clone-INFINITY order-WebDataClone-WebFS-mandatory order-WebFS-WebSite-mandatory - order-dlm-clone-WebFS-clone-mandatory + order-dlm-clone-WebFS-mandatory ---- ==== Apache ==== Lastly, we have the actual service, Apache. We need only tell the cluster where to find its main configuration file and restrict it to running on nodes that have the required filesystem mounted and the IP address active. ---- [root@pcmk-1 ~]# pcs resource show WebSite-clone Clone: WebSite-clone Resource: WebSite (class=ocf provider=heartbeat type=apache) - Attributes: configfile=/etc/httpd/conf/httpd.conf statusurl=http://localhost/server-status - Operations: start interval=0s timeout=40s (WebSite-start-timeout-40s) - stop interval=0s timeout=60s (WebSite-stop-timeout-60s) - monitor interval=1min (WebSite-monitor-interval-1min) + Attributes: configfile=/etc/httpd/conf/httpd.conf statusurl=http://localhost/server-status + Operations: monitor interval=1min (WebSite-monitor-interval-1min) + start interval=0s timeout=40s (WebSite-start-interval-0s) + stop interval=0s timeout=60s (WebSite-stop-interval-0s) [root@pcmk-1 ~]# pcs constraint ref WebSite-clone Resource: WebSite-clone colocation-WebSite-ClusterIP-INFINITY colocation-WebSite-WebFS-INFINITY order-ClusterIP-WebSite-mandatory order-WebFS-WebSite-mandatory ---- diff --git a/doc/Clusters_from_Scratch/en-US/Ap-Corosync-Conf.txt b/doc/Clusters_from_Scratch/en-US/Ap-Corosync-Conf.txt index a00e9a2e5a..ea286275da 100644 --- a/doc/Clusters_from_Scratch/en-US/Ap-Corosync-Conf.txt +++ b/doc/Clusters_from_Scratch/en-US/Ap-Corosync-Conf.txt @@ -1,34 +1,37 @@ :compat-mode: legacy [appendix] [[ap-corosync-conf]] == Sample Corosync Configuration == .Sample +corosync.conf+ for two-node cluster created by `pcs`. ..... totem { -version: 2 -secauth: off -cluster_name: mycluster -transport: udpu + version: 2 + cluster_name: mycluster + secauth: off + transport: udpu } nodelist { - node { + node { ring0_addr: pcmk-1 nodeid: 1 - } - node { + } + + node { ring0_addr: pcmk-2 nodeid: 2 - } + } } quorum { -provider: corosync_votequorum -two_node: 1 + provider: corosync_votequorum + two_node: 1 } logging { -to_syslog: yes + to_logfile: yes + logfile: /var/log/cluster/corosync.log + to_syslog: yes } ..... diff --git a/doc/Clusters_from_Scratch/en-US/Ap-Reading.txt b/doc/Clusters_from_Scratch/en-US/Ap-Reading.txt index eac4ad3b37..750fd74b2a 100644 --- a/doc/Clusters_from_Scratch/en-US/Ap-Reading.txt +++ b/doc/Clusters_from_Scratch/en-US/Ap-Reading.txt @@ -1,13 +1,11 @@ :compat-mode: legacy [appendix] == Further Reading == -- Project Website -http://www.clusterlabs.org/ +- Project Website https://www.clusterlabs.org/ - SuSE has a comprehensive guide to cluster commands (though using the `crmsh` command-line shell rather than `pcs`) at: https://www.suse.com/documentation/sle_ha/book_sleha/data/book_sleha.html -- Corosync - http://www.corosync.org/ +- Corosync http://www.corosync.org/ diff --git a/doc/Clusters_from_Scratch/en-US/Book_Info.xml b/doc/Clusters_from_Scratch/en-US/Book_Info.xml index 54b4b8b623..cfabd51e1c 100644 --- a/doc/Clusters_from_Scratch/en-US/Book_Info.xml +++ b/doc/Clusters_from_Scratch/en-US/Book_Info.xml @@ -1,71 +1,71 @@ %BOOK_ENTITIES; ]> Clusters from Scratch Step-by-Step Instructions for Building Your First High-Availability Cluster Pacemaker 2.0 - 9 + 10 1 This document provides a step-by-step guide to building a simple high-availability cluster using Pacemaker. The example cluster will use: &DISTRO; &DISTRO_VERSION; as the host operating system Corosync to provide messaging and membership services, - Pacemaker 1.1.16 + Pacemaker 1.1.18 While this guide is part of the document set for Pacemaker 2.0, it demonstrates the version available in the standard &DISTRO; repositories to perform resource management, DRBD as a cost-effective alternative to shared storage, GFS2 as the cluster filesystem (in active/active mode) Given the graphical nature of the install process, a number of screenshots are included. However the guide is primarily composed of commands, the reasons for executing them and their expected outputs. diff --git a/doc/Clusters_from_Scratch/en-US/Ch-Active-Active.txt b/doc/Clusters_from_Scratch/en-US/Ch-Active-Active.txt index a88643e887..0923666353 100644 --- a/doc/Clusters_from_Scratch/en-US/Ch-Active-Active.txt +++ b/doc/Clusters_from_Scratch/en-US/Ch-Active-Active.txt @@ -1,375 +1,383 @@ :compat-mode: legacy = Convert Cluster to Active/Active = The primary requirement for an Active/Active cluster is that the data required for your services is available, simultaneously, on both machines. Pacemaker makes no requirement on how this is achieved; you could use a SAN if you had one available, but since DRBD supports multiple Primaries, we can continue to use it here. == Install Cluster Filesystem Software == The only hitch is that we need to use a cluster-aware filesystem. The one we used earlier with DRBD, xfs, is not one of those. Both OCFS2 and GFS2 are supported; here, we will use GFS2. On both nodes, install the GFS2 command-line utilities and the Distributed Lock Manager (DLM) required by cluster filesystems: ---- # yum install -y gfs2-utils dlm ---- == Configure the Cluster for the DLM == The DLM needs to run on both nodes, so we'll start by creating a resource for it (using the *ocf:pacemaker:controld* resource script), and clone it: ---- [root@pcmk-1 ~]# pcs cluster cib dlm_cfg -[root@pcmk-1 ~]# pcs -f dlm_cfg resource create dlm ocf:pacemaker:controld op monitor interval=60s +[root@pcmk-1 ~]# pcs -f dlm_cfg resource create dlm \ + ocf:pacemaker:controld op monitor interval=60s [root@pcmk-1 ~]# pcs -f dlm_cfg resource clone dlm clone-max=2 clone-node-max=1 [root@pcmk-1 ~]# pcs -f dlm_cfg resource show - ClusterIP (ocf::heartbeat:IPaddr2): Started - WebSite (ocf::heartbeat:apache): Started + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + WebSite (ocf::heartbeat:apache): Started pcmk-1 Master/Slave Set: WebDataClone [WebData] - Masters: [ pcmk-2 ] - Slaves: [ pcmk-1 ] - WebFS (ocf::heartbeat:Filesystem): Started + Masters: [ pcmk-1 ] + Slaves: [ pcmk-2 ] + WebFS (ocf::heartbeat:Filesystem): Started pcmk-1 Clone Set: dlm-clone [dlm] Stopped: [ pcmk-1 pcmk-2 ] ---- Activate our new configuration, and see how the cluster responds: ---- -[root@pcmk-1 ~]# pcs cluster cib-push dlm_cfg +[root@pcmk-1 ~]# pcs cluster cib-push dlm_cfg --config CIB updated [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-1 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 11:19:36 2018 -Last change: Fri Jan 12 11:19:28 2018 +Current DC: pcmk-1 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Tue Sep 11 10:18:30 2018 +Last change: Tue Sep 11 10:16:49 2018 by hacluster via crmd on pcmk-2 2 nodes configured 8 resources configured Online: [ pcmk-1 pcmk-2 ] Full list of resources: - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 - WebSite (ocf::heartbeat:apache): Started pcmk-2 + ipmi-fencing (stonith:fence_ipmilan): Started pcmk-1 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + WebSite (ocf::heartbeat:apache): Started pcmk-1 Master/Slave Set: WebDataClone [WebData] - Masters: [ pcmk-2 ] - Slaves: [ pcmk-1 ] - WebFS (ocf::heartbeat:Filesystem): Started pcmk-2 - ipmi-fencing (stonith:fence_ipmilan): Started pcmk-1 + Masters: [ pcmk-1 ] + Slaves: [ pcmk-2 ] + WebFS (ocf::heartbeat:Filesystem): Started pcmk-1 Clone Set: dlm-clone [dlm] Started: [ pcmk-1 pcmk-2 ] Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ---- [[GFS2_prep]] == Create and Populate GFS2 Filesystem == Before we do anything to the existing partition, we need to make sure it is unmounted. We do this by telling the cluster to stop the WebFS resource. This will ensure that other resources (in our case, Apache) using WebFS are not only stopped, but stopped in the correct order. ---- [root@pcmk-1 ~]# pcs resource disable WebFS [root@pcmk-1 ~]# pcs resource - ClusterIP (ocf::heartbeat:IPaddr2): Started - WebSite (ocf::heartbeat:apache): Stopped + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + WebSite (ocf::heartbeat:apache): Stopped Master/Slave Set: WebDataClone [WebData] - Masters: [ pcmk-2 ] - Slaves: [ pcmk-1 ] - WebFS (ocf::heartbeat:Filesystem): Stopped + Masters: [ pcmk-1 ] + Slaves: [ pcmk-2 ] + WebFS (ocf::heartbeat:Filesystem): Stopped (disabled) Clone Set: dlm-clone [dlm] Started: [ pcmk-1 pcmk-2 ] ---- You can see that both Apache and WebFS have been stopped, -and that *pcmk-2* is the current master for the DRBD device. +and that *pcmk-1* is the current master for the DRBD device. Now we can create a new GFS2 filesystem on the DRBD device. [WARNING] ========= This will erase all previous content stored on the DRBD device. Ensure you have a copy of any important data. ========= [IMPORTANT] =========== Run the next command on whichever node has the DRBD Primary role. Otherwise, you will receive the message: ----- /dev/drbd1: Read-only file system ----- =========== ----- -[root@pcmk-2 ~]# mkfs.gfs2 -p lock_dlm -j 2 -t mycluster:web /dev/drbd1 +[root@pcmk-1 ~]# mkfs.gfs2 -p lock_dlm -j 2 -t mycluster:web /dev/drbd1 It appears to contain an existing filesystem (xfs) This will destroy any data on /dev/drbd1 -Are you sure you want to proceed? [y/n]y +Are you sure you want to proceed? [y/n] y +Discarding device contents (may take a while on large devices): Done +Adding journals: Done +Building resource groups: Done +Creating quota file: Done +Writing superblock and syncing: Done Device: /dev/drbd1 Block size: 4096 -Device size: 1.00 GB (262127 blocks) -Filesystem size: 1.00 GB (262126 blocks) +Device size: 0.50 GB (131059 blocks) +Filesystem size: 0.50 GB (131056 blocks) Journals: 2 -Resource groups: 5 +Resource groups: 3 Locking protocol: "lock_dlm" Lock table: "mycluster:web" -UUID: 9a72c488-d8a7-24c9-ceee-add7a8ca52c2 +UUID: 0bcbffab-cada-4105-94d1-be8a26669ee0 ----- The `mkfs.gfs2` command required a number of additional parameters: * `-p lock_dlm` specifies that we want to use the kernel's DLM. * `-j 2` indicates that the filesystem should reserve enough space for two journals (one for each node that will access the filesystem). * `-t mycluster:web` specifies the lock table name. The format for this field is +pass:[clustername:fsname]+. For +pass:[clustername]+, we need to use the same value we specified originally with `pcs cluster setup --name` (which is also the value of *cluster_name* in +/etc/corosync/corosync.conf+). If you are unsure what your cluster name is, you can look in +/etc/corosync/corosync.conf+ or execute the command `pcs cluster corosync pcmk-1 | grep cluster_name`. Now we can (re-)populate the new filesystem with data (web pages). We'll create yet another variation on our home page. ----- -[root@pcmk-2 ~]# mount /dev/drbd1 /mnt -[root@pcmk-2 ~]# cat <<-END >/mnt/index.html +[root@pcmk-1 ~]# mount /dev/drbd1 /mnt +[root@pcmk-1 ~]# cat <<-END >/mnt/index.html My Test Site - GFS2 END -[root@pcmk-2 ~]# chcon -R --reference=/var/www/html /mnt -[root@pcmk-2 ~]# umount /dev/drbd1 -[root@pcmk-2 ~]# drbdadm verify wwwdata +[root@pcmk-1 ~]# chcon -R --reference=/var/www/html /mnt +[root@pcmk-1 ~]# umount /dev/drbd1 +[root@pcmk-1 ~]# drbdadm verify wwwdata ----- == Reconfigure the Cluster for GFS2 == With the WebFS resource stopped, let's update the configuration. ---- [root@pcmk-1 ~]# pcs resource show WebFS Resource: WebFS (class=ocf provider=heartbeat type=Filesystem) Attributes: device=/dev/drbd1 directory=/var/www/html fstype=xfs - Meta Attrs: target-role=Stopped - Operations: start interval=0s timeout=60 (WebFS-start-timeout-60) - stop interval=0s timeout=60 (WebFS-stop-timeout-60) - monitor interval=20 timeout=40 (WebFS-monitor-interval-20) + Meta Attrs: target-role=Stopped + Operations: monitor interval=20 timeout=40 (WebFS-monitor-interval-20) + notify interval=0s timeout=60 (WebFS-notify-interval-0s) + start interval=0s timeout=60 (WebFS-start-interval-0s) + stop interval=0s timeout=60 (WebFS-stop-interval-0s) ---- The fstype option needs to be updated to *gfs2* instead of *xfs*. ---- [root@pcmk-1 ~]# pcs resource update WebFS fstype=gfs2 [root@pcmk-1 ~]# pcs resource show WebFS Resource: WebFS (class=ocf provider=heartbeat type=Filesystem) - Attributes: device=/dev/drbd1 directory=/var/www/html fstype=gfs2 + Attributes: device=/dev/drbd1 directory=/var/www/html fstype=gfs2 Meta Attrs: target-role=Stopped - Operations: start interval=0s timeout=60 (WebFS-start-timeout-60) - stop interval=0s timeout=60 (WebFS-stop-timeout-60) - monitor interval=20 timeout=40 (WebFS-monitor-interval-20) + Operations: monitor interval=20 timeout=40 (WebFS-monitor-interval-20) + notify interval=0s timeout=60 (WebFS-notify-interval-0s) + start interval=0s timeout=60 (WebFS-start-interval-0s) + stop interval=0s timeout=60 (WebFS-stop-interval-0s) ---- GFS2 requires that DLM be running, so we also need to set up new colocation and ordering constraints for it: ---- [root@pcmk-1 ~]# pcs constraint colocation add WebFS with dlm-clone INFINITY [root@pcmk-1 ~]# pcs constraint order dlm-clone then WebFS Adding dlm-clone WebFS (kind: Mandatory) (Options: first-action=start then-action=start) ---- == Clone the IP address == There's no point making the services active on both locations if we can't reach them both, so let's clone the IP address. The *IPaddr2* resource agent has built-in intelligence for when it is configured as a clone. It will utilize a multicast MAC address to have the local switch send the relevant packets to all nodes in the cluster, together with *iptables clusterip* rules on the nodes so that any given packet will be grabbed by exactly one node. This will give us a simple but effective form of load-balancing requests between our two nodes. Let's start a new config, and clone our IP: ---- [root@pcmk-1 ~]# pcs cluster cib loadbalance_cfg [root@pcmk-1 ~]# pcs -f loadbalance_cfg resource clone ClusterIP \ clone-max=2 clone-node-max=2 globally-unique=true ---- * `clone-max=2` tells the resource agent to split packets this many ways. This should equal the number of nodes that can host the IP. * `clone-node-max=2` says that one node can run up to 2 instances of the clone. This should also equal the number of nodes that can host the IP, so that if any node goes down, another node can take over the failed node's "request bucket". Otherwise, requests intended for the failed node would be discarded. * `globally-unique=true` tells the cluster that one clone isn't identical to another (each handles a different "bucket"). This also tells the resource agent to insert *iptables* rules so each host only processes packets in its bucket(s). Notice that when the ClusterIP becomes a clone, the constraints referencing ClusterIP now reference the clone. This is done automatically by pcs. ---- [root@pcmk-1 ~]# pcs -f loadbalance_cfg constraint Location Constraints: Ordering Constraints: start ClusterIP-clone then start WebSite (kind:Mandatory) promote WebDataClone then start WebFS (kind:Mandatory) start WebFS then start WebSite (kind:Mandatory) start dlm-clone then start WebFS (kind:Mandatory) Colocation Constraints: WebSite with ClusterIP-clone (score:INFINITY) WebFS with WebDataClone (score:INFINITY) (with-rsc-role:Master) WebSite with WebFS (score:INFINITY) WebFS with dlm-clone (score:INFINITY) Ticket Constraints: ---- Now we must tell the resource how to decide which requests are processed by which hosts. To do this, we specify the *clusterip_hash* parameter. The value of *sourceip* means that the source IP address of incoming packets will be hashed; each node will process a certain range of hashes. ---- [root@pcmk-1 ~]# pcs -f loadbalance_cfg resource update ClusterIP clusterip_hash=sourceip ---- Load our configuration to the cluster, and see how it responds. ----- -[root@pcmk-1 ~]# pcs cluster cib-push loadbalance_cfg +[root@pcmk-1 ~]# pcs cluster cib-push loadbalance_cfg --config CIB updated [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-1 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 11:32:07 2018 -Last change: Fri Jan 12 11:32:04 2018 +Current DC: pcmk-1 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Tue Sep 11 10:36:38 2018 +Last change: Tue Sep 11 10:36:33 2018 by root via cibadmin on pcmk-1 2 nodes configured -9 resources configured +9 resources configured (1 DISABLED) Online: [ pcmk-1 pcmk-2 ] Full list of resources: - WebSite (ocf::heartbeat:apache): Stopped + ipmi-fencing (stonith:fence_ipmilan): Started pcmk-1 + WebSite (ocf::heartbeat:apache): Stopped Master/Slave Set: WebDataClone [WebData] Masters: [ pcmk-1 ] Slaves: [ pcmk-2 ] - WebFS (ocf::heartbeat:Filesystem): Stopped - ipmi-fencing (stonith:fence_ipmilan): Started pcmk-1 + WebFS (ocf::heartbeat:Filesystem): Stopped (disabled) Clone Set: dlm-clone [dlm] Started: [ pcmk-1 pcmk-2 ] Clone Set: ClusterIP-clone [ClusterIP] (unique) - ClusterIP:0 (ocf::heartbeat:IPaddr2): Started pcmk-1 - ClusterIP:1 (ocf::heartbeat:IPaddr2): Started pcmk-2 + ClusterIP:0 (ocf::heartbeat:IPaddr2): Started pcmk-2 + ClusterIP:1 (ocf::heartbeat:IPaddr2): Started pcmk-1 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ----- If desired, you can demonstrate that all request buckets are working by using a tool such as `arping` from several source hosts to see which host responds to each. == Clone the Filesystem and Apache Resources == Now that we have a cluster filesystem ready to go, and our nodes can load-balance requests to a shared IP address, we can configure the cluster so both nodes mount the filesystem and respond to web requests. Clone the filesystem and Apache resources in a new configuration. Notice how pcs automatically updates the relevant constraints again. ---- [root@pcmk-1 ~]# pcs cluster cib active_cfg [root@pcmk-1 ~]# pcs -f active_cfg resource clone WebFS [root@pcmk-1 ~]# pcs -f active_cfg resource clone WebSite [root@pcmk-1 ~]# pcs -f active_cfg constraint Location Constraints: Ordering Constraints: start ClusterIP-clone then start WebSite-clone (kind:Mandatory) promote WebDataClone then start WebFS-clone (kind:Mandatory) start WebFS-clone then start WebSite-clone (kind:Mandatory) start dlm-clone then start WebFS-clone (kind:Mandatory) Colocation Constraints: WebSite-clone with ClusterIP-clone (score:INFINITY) WebFS-clone with WebDataClone (score:INFINITY) (with-rsc-role:Master) WebSite-clone with WebFS-clone (score:INFINITY) WebFS-clone with dlm-clone (score:INFINITY) Ticket Constraints: ---- Tell the cluster that it is now allowed to promote both instances to be DRBD Primary (aka. master). ----- -[root@pcmk-1 ~]# pcs -f active_cfg resource update WebDataClone master-max=2 +[root@pcmk-1 ~]# pcs -f active_cfg resource update WebDataClone master-max=2 ----- Finally, load our configuration to the cluster, and re-enable the WebFS resource (which we disabled earlier). ----- -[root@pcmk-1 ~]# pcs cluster cib-push active_cfg +[root@pcmk-1 ~]# pcs cluster cib-push active_cfg --config CIB updated [root@pcmk-1 ~]# pcs resource enable WebFS ----- After all the processes are started, the status should look similar to this. ----- [root@pcmk-1 ~]# pcs resource Master/Slave Set: WebDataClone [WebData] Masters: [ pcmk-1 pcmk-2 ] Clone Set: dlm-clone [dlm] Started: [ pcmk-1 pcmk-2 ] Clone Set: ClusterIP-clone [ClusterIP] (unique) - ClusterIP:0 (ocf::heartbeat:IPaddr2): Started - ClusterIP:1 (ocf::heartbeat:IPaddr2): Started + ClusterIP:0 (ocf::heartbeat:IPaddr2): Started pcmk-2 + ClusterIP:1 (ocf::heartbeat:IPaddr2): Started pcmk-1 Clone Set: WebFS-clone [WebFS] Started: [ pcmk-1 pcmk-2 ] Clone Set: WebSite-clone [WebSite] Started: [ pcmk-1 pcmk-2 ] ----- == Test Failover == Testing failover is left as an exercise for the reader. For example, you can put one node into standby mode, use `pcs status` to confirm that its ClusterIP clone was moved to the other node, and use `arping` to verify that packets are not being lost from any source host. [NOTE] ==== You may find that when a failed node rejoins the cluster, both ClusterIP clones stay on one node, due to the resource stickiness. While this works fine, it effectively eliminates load-balancing and returns the cluster to an active-passive setup again. You can avoid this by disabling stickiness for the IP address resource: ---- [root@pcmk-1 ~]# pcs resource meta ClusterIP resource-stickiness=0 ---- ==== diff --git a/doc/Clusters_from_Scratch/en-US/Ch-Active-Passive.txt b/doc/Clusters_from_Scratch/en-US/Ch-Active-Passive.txt index 31e9eac2ef..b0d950c5e1 100644 --- a/doc/Clusters_from_Scratch/en-US/Ch-Active-Passive.txt +++ b/doc/Clusters_from_Scratch/en-US/Ch-Active-Passive.txt @@ -1,392 +1,377 @@ :compat-mode: legacy = Create an Active/Passive Cluster = == Explore the Existing Configuration == When Pacemaker starts up, it automatically records the number and details of the nodes in the cluster, as well as which stack is being used and the version of Pacemaker being used. The first few lines of output should look like this: ---- [root@pcmk-1 ~]# pcs status Cluster name: mycluster WARNING: no stonith devices and stonith-enabled is not false Stack: corosync -Current DC: pcmk-2 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 16:15:29 2018 -Last change: Fri Jan 12 15:49:47 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 16:41:46 2018 +Last change: Mon Sep 10 16:30:53 2018 by hacluster via crmd on pcmk-2 2 nodes configured 0 resources configured Online: [ pcmk-1 pcmk-2 ] ---- For those who are not of afraid of XML, you can see the raw cluster configuration and status by using the `pcs cluster cib` command. .The last XML you'll see in this document ====== ---- [root@pcmk-1 ~]# pcs cluster cib ---- [source,XML] ---- - + - + - - + + - - - - - - - - + + - - - - - - ---- ====== Before we make any changes, it's a good idea to check the validity of the configuration. ---- [root@pcmk-1 ~]# crm_verify -L -V error: unpack_resources: Resource start-up disabled since no STONITH resources have been defined error: unpack_resources: Either configure some or disable STONITH with the stonith-enabled option error: unpack_resources: NOTE: Clusters with shared data need STONITH to ensure data integrity Errors found during check: config not valid ---- As you can see, the tool has found some errors. In order to guarantee the safety of your data, footnote:[If the data is corrupt, there is little point in continuing to make it available] -the default for STONITH -footnote:[A common node fencing mechanism. Used to ensure data integrity by powering off "bad" nodes] -in Pacemaker is *enabled*. However, it also knows when no STONITH configuration has been -supplied and reports this as a problem (since the cluster would not be -able to make progress if a situation requiring node fencing arose). +fencing (also called STONITH) is enabled by default. However, it also knows +when no STONITH configuration has been supplied and reports this as a problem +(since the cluster will not be able to make progress if a situation requiring +node fencing arises). We will disable this feature for now and configure it later. To disable STONITH, set the *stonith-enabled* cluster option to false: ---- [root@pcmk-1 ~]# pcs property set stonith-enabled=false [root@pcmk-1 ~]# crm_verify -L ---- With the new cluster option set, the configuration is now valid. [WARNING] ========= The use of `stonith-enabled=false` is completely inappropriate for a production cluster. It tells the cluster to simply pretend that failed nodes are safely powered off. Some vendors will refuse to support clusters that have -STONITH disabled. - -We disable STONITH here only to defer the discussion of its +STONITH disabled. We disable STONITH here only to defer the discussion of its configuration, which can differ widely from one installation to the next. See <<_what_is_stonith>> for information on why STONITH is important and details on how to configure it. ========= == Add a Resource == Our first resource will be a unique IP address that the cluster can bring up on either node. Regardless of where any cluster service(s) are running, end users need a consistent address to contact them on. Here, I will choose 192.168.122.120 as the floating address, give it the imaginative name ClusterIP and tell the cluster to check whether it is running every 30 seconds. [WARNING] =========== The chosen address must not already be in use on the network. Do not reuse an IP address one of the nodes already has configured. =========== ---- [root@pcmk-1 ~]# pcs resource create ClusterIP ocf:heartbeat:IPaddr2 \ ip=192.168.122.120 cidr_netmask=32 op monitor interval=30s ---- Another important piece of information here is *ocf:heartbeat:IPaddr2*. This tells Pacemaker three things about the resource you want to add: * The first field (*ocf* in this case) is the standard to which the resource script conforms and where to find it. * The second field (*heartbeat* in this case) is standard-specific; for OCF resources, it tells the cluster which OCF namespace the resource script is in. * The third field (*IPaddr2* in this case) is the name of the resource script. To obtain a list of the available resource standards (the *ocf* part of *ocf:heartbeat:IPaddr2*), run: ---- [root@pcmk-1 ~]# pcs resource standards lsb ocf service systemd ---- To obtain a list of the available OCF resource providers (the *heartbeat* part of *ocf:heartbeat:IPaddr2*), run: ---- [root@pcmk-1 ~]# pcs resource providers heartbeat openstack pacemaker ---- Finally, if you want to see all the resource agents available for a specific OCF provider (the *IPaddr2* part of *ocf:heartbeat:IPaddr2*), run: ---- [root@pcmk-1 ~]# pcs resource agents ocf:heartbeat apache +aws-vpc-move-ip +awseip +awsvip +azure-lb clvm -conntrackd -CTDB -db2 -Delay . . (skipping lots of resources to save space) . symlink tomcat VirtualDomain Xinetd ---- Now, verify that the IP resource has been added, and display the cluster's status to see that it is now active: ---- [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-1 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 17:44:40 2018 -Last change: Fri Jan 12 17:44:26 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 16:55:26 2018 +Last change: Mon Sep 10 16:53:42 2018 by root via cibadmin on pcmk-1 2 nodes configured -1 resources configured +1 resource configured Online: [ pcmk-1 pcmk-2 ] Full list of resources: - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ---- == Perform a Failover == Since our ultimate goal is high availability, we should test failover of our new resource before moving on. First, find the node on which the IP address is running. ---- [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-1 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 17:44:40 2018 -Last change: Fri Jan 12 17:44:26 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 16:55:26 2018 +Last change: Mon Sep 10 16:53:42 2018 by root via cibadmin on pcmk-1 2 nodes configured -1 resources configured +1 resource configured Online: [ pcmk-1 pcmk-2 ] Full list of resources: - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 ---- You can see that the status of the *ClusterIP* resource is *Started* on a particular node (in this example, *pcmk-1*). Shut down Pacemaker and Corosync on that machine to trigger a failover. ---- [root@pcmk-1 ~]# pcs cluster stop pcmk-1 Stopping Cluster (pacemaker)... Stopping Cluster (corosync)... ---- [NOTE] ====== A cluster command such as +pcs cluster stop pass:[nodename]+ can be run from any node in the cluster, not just the affected node. ====== Verify that pacemaker and corosync are no longer running: ---- [root@pcmk-1 ~]# pcs status Error: cluster is not currently running on this node ---- Go to the other node, and check the cluster status. ---- [root@pcmk-2 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-2 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 18:30:56 2018 -Last change: Fri Jan 12 17:44:26 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 16:57:22 2018 +Last change: Mon Sep 10 16:53:42 2018 by root via cibadmin on pcmk-1 2 nodes configured -1 resources configured +1 resource configured Online: [ pcmk-2 ] OFFLINE: [ pcmk-1 ] Full list of resources: - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ---- Notice that *pcmk-1* is *OFFLINE* for cluster purposes (its *pcsd* is still active, allowing it to receive `pcs` commands, but it is not participating in the cluster). Also notice that *ClusterIP* is now running on *pcmk-2* -- failover happened automatically, and no errors are reported. [IMPORTANT] .Quorum ==== If a cluster splits into two (or more) groups of nodes that can no longer communicate with each other (aka. _partitions_), _quorum_ is used to prevent resources from starting on more nodes than desired, which would risk data corruption. A cluster has quorum when more than half of all known nodes are online in the same partition, or for the mathematically inclined, whenever the following equation is true: .... total_nodes < 2 * active_nodes .... For example, if a 5-node cluster split into 3- and 2-node paritions, the 3-node partition would have quorum and could continue serving resources. If a 6-node cluster split into two 3-node partitions, neither partition would have quorum; pacemaker's default behavior in such cases is to stop all resources, in order to prevent data corruption. Two-node clusters are a special case. By the above definition, a two-node cluster would only have quorum when both nodes are running. This would make the creation of a two-node cluster pointless, -footnote:[Some would argue that two-node clusters are always pointless, but that is an argument for another time] but corosync has the ability to treat two-node clusters as if only one node is required for quorum. The `pcs cluster setup` command will automatically configure *two_node: 1* in +corosync.conf+, so a two-node cluster will "just work". If you are using a different cluster shell, you will have to configure +corosync.conf+ appropriately yourself. ==== Now, simulate node recovery by restarting the cluster stack on *pcmk-1*, and check the cluster's status. (It may take a little while before the cluster gets going on the node, but it eventually will look like the below.) ---- [root@pcmk-1 ~]# pcs cluster start pcmk-1 pcmk-1: Starting Cluster... [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-2 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 18:50:11 2018 -Last change: Fri Jan 12 17:44:26 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 17:00:04 2018 +Last change: Mon Sep 10 16:53:42 2018 by root via cibadmin on pcmk-1 2 nodes configured -1 resources configured +1 resource configured Online: [ pcmk-1 pcmk-2 ] Full list of resources: - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ---- == Prevent Resources from Moving after Recovery == In most circumstances, it is highly desirable to prevent healthy resources from being moved around the cluster. Moving resources almost always requires a period of downtime. For complex services such as databases, this period can be quite long. To address this, Pacemaker has the concept of resource _stickiness_, which controls how strongly a service prefers to stay running where it is. You may like to think of it as the "cost" of any downtime. By default, Pacemaker assumes there is zero cost associated with moving resources and will do so to achieve "optimal" footnote:[Pacemaker's definition of optimal may not always agree with that of a human's. The order in which Pacemaker processes lists of resources and nodes creates implicit preferences in situations where the administrator has not explicitly specified them.] resource placement. We can specify a different stickiness for every resource, but it is often sufficient to change the default. ---- [root@pcmk-1 ~]# pcs resource defaults resource-stickiness=100 +Warning: Defaults do not apply to resources which override them with their own defined values [root@pcmk-1 ~]# pcs resource defaults resource-stickiness: 100 ---- diff --git a/doc/Clusters_from_Scratch/en-US/Ch-Apache.txt b/doc/Clusters_from_Scratch/en-US/Ch-Apache.txt index 5d73526b83..efa2c763b5 100644 --- a/doc/Clusters_from_Scratch/en-US/Ch-Apache.txt +++ b/doc/Clusters_from_Scratch/en-US/Ch-Apache.txt @@ -1,416 +1,424 @@ :compat-mode: legacy = Add Apache HTTP Server as a Cluster Service = indexterm:[Apache HTTP Server] Now that we have a basic but functional active/passive two-node cluster, we're ready to add some real services. We're going to start with Apache HTTP Server because it is a feature of many clusters and relatively simple to configure. == Install Apache == Before continuing, we need to make sure Apache is installed on both hosts. We also need the wget tool in order for the cluster to be able to check the status of the Apache server. ---- # yum install -y httpd wget # firewall-cmd --permanent --add-service=http # firewall-cmd --reload ---- [IMPORTANT] ==== Do *not* enable the httpd service. Services that are intended to be managed via the cluster software should never be managed by the OS. - It is often useful, however, to manually start the service, verify that it works, then stop it again, before adding it to the cluster. This allows you to resolve any non-cluster-related problems before continuing. Since this is a simple example, we'll skip that step here. ==== == Create Website Documents == We need to create a page for Apache to serve. On &DISTRO; &DISTRO_VERSION;, the default Apache document root is /var/www/html, so we'll create an index file there. For the moment, we will simplify things by serving a static site and manually synchronizing the data between the two nodes, so run this command on both nodes: ----- # cat <<-END >/var/www/html/index.html My Test Site - $(hostname) END ----- == Enable the Apache status URL == indexterm:[Apache HTTP Server,/server-status] In order to monitor the health of your Apache instance, and recover it if it fails, the resource agent used by Pacemaker assumes the server-status URL is available. On both nodes, enable the URL with: ---- # cat <<-END >/etc/httpd/conf.d/status.conf SetHandler server-status Require local END ---- [NOTE] ====== If you are using a different operating system, server-status may already be enabled or may be configurable in a different location. If you are using a version of Apache HTTP Server less than 2.4, the syntax will be different. ====== == Configure the Cluster == indexterm:[Apache HTTP Server,Apache resource configuration] At this point, Apache is ready to go, and all that needs to be done is to add it to the cluster. Let's call the resource WebSite. We need to use an OCF resource script called apache in the heartbeat namespace. footnote:[Compare the key used here, *ocf:heartbeat:apache*, with the one we used earlier for the IP address, *ocf:heartbeat:IPaddr2*] The script's only required parameter is the path to the main Apache configuration file, and we'll tell the cluster to check once a minute that Apache is still running. ---- [root@pcmk-1 ~]# pcs resource create WebSite ocf:heartbeat:apache \ configfile=/etc/httpd/conf/httpd.conf \ statusurl="http://localhost/server-status" \ op monitor interval=1min ---- By default, the operation timeout for all resources' start, stop, and monitor operations is 20 seconds. In many cases, this timeout period is less than a particular resource's advised timeout period. For the purposes of this tutorial, we will adjust the global operation timeout default to 240 seconds. ---- [root@pcmk-1 ~]# pcs resource op defaults timeout=240s +Warning: Defaults do not apply to resources which override them with their own defined values [root@pcmk-1 ~]# pcs resource op defaults timeout: 240s ---- [NOTE] ====== In a production cluster, it is usually better to adjust each resource's start, stop, and monitor timeouts to values that are appropriate to the behavior observed in your environment, rather than adjust the global default. ====== After a short delay, we should see the cluster start Apache. ----- [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-2 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 12:40:41 2018 -Last change: Fri Jan 12 12:40:05 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 17:06:22 2018 +Last change: Mon Sep 10 17:05:41 2018 by root via cibadmin on pcmk-1 2 nodes configured 2 resources configured Online: [ pcmk-1 pcmk-2 ] Full list of resources: - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 - WebSite (ocf::heartbeat:apache): Started pcmk-1 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + WebSite (ocf::heartbeat:apache): Started pcmk-1 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ----- Wait a moment, the WebSite resource isn't running on the same host as our IP address! [NOTE] ====== If, in the `pcs status` output, you see the WebSite resource has failed to start, then you've likely not enabled the status URL correctly. You can check whether this is the problem by running: .... wget -O - http://localhost/server-status .... If you see *Not Found* or *Forbidden* in the output, then this is likely the problem. Ensure that the ** block is correct. ====== == Ensure Resources Run on the Same Host == To reduce the load on any one machine, Pacemaker will generally try to spread the configured resources across the cluster nodes. However, we can tell the cluster that two resources are related and need to run on the same host (or not at all). Here, we instruct the cluster that WebSite can only run on the host that ClusterIP is active on. To achieve this, we use a _colocation constraint_ that indicates it is mandatory for WebSite to run on the same node as ClusterIP. The "mandatory" part of the colocation constraint is indicated by using a score of INFINITY. The INFINITY score also means that if ClusterIP is not active anywhere, WebSite will not be permitted to run. [NOTE] ======= If ClusterIP is not active anywhere, WebSite will not be permitted to run anywhere. ======= [IMPORTANT] =========== Colocation constraints are "directional", in that they imply certain things about the order in which the two resources will have a location chosen. In this case, we're saying that *WebSite* needs to be placed on the same machine as *ClusterIP*, which implies that the cluster must know the location of *ClusterIP* before choosing a location for *WebSite*. =========== ----- [root@pcmk-1 ~]# pcs constraint colocation add WebSite with ClusterIP INFINITY [root@pcmk-1 ~]# pcs constraint Location Constraints: Ordering Constraints: Colocation Constraints: WebSite with ClusterIP (score:INFINITY) Ticket Constraints: [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-2 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 13:57:58 2018 -Last change: Fri Jan 12 13:57:22 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 17:08:54 2018 +Last change: Mon Sep 10 17:08:27 2018 by root via cibadmin on pcmk-1 2 nodes configured 2 resources configured Online: [ pcmk-1 pcmk-2 ] Full list of resources: - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 - WebSite (ocf::heartbeat:apache): Started pcmk-2 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + WebSite (ocf::heartbeat:apache): Started pcmk-2 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ----- == Ensure Resources Start and Stop in Order == Like many services, Apache can be configured to bind to specific IP addresses on a host or to the wildcard IP address. If Apache binds to the wildcard, it doesn't matter whether an IP address is added before or after Apache starts; Apache will respond on that IP just the same. However, if Apache binds only to certain IP address(es), the order matters: If the address is added after Apache starts, Apache won't respond on that address. To be sure our WebSite responds regardless of Apache's address configuration, we need to make sure ClusterIP not only runs on the same node, but starts before WebSite. A colocation constraint only ensures the resources run together, not the order in which they are started and stopped. We do this by adding an ordering constraint. By default, all order constraints are mandatory, which means that the recovery of ClusterIP will also trigger the recovery of WebSite. ----- [root@pcmk-1 ~]# pcs constraint order ClusterIP then WebSite Adding ClusterIP WebSite (kind: Mandatory) (Options: first-action=start then-action=start) [root@pcmk-1 ~]# pcs constraint Location Constraints: Ordering Constraints: start ClusterIP then start WebSite (kind:Mandatory) Colocation Constraints: WebSite with ClusterIP (score:INFINITY) Ticket Constraints: ----- == Prefer One Node Over Another == Pacemaker does not rely on any sort of hardware symmetry between nodes, -so it may well be that one machine is more powerful than the other. In -such cases, it makes sense to host the resources on the more powerful node if -it is available. To do this, we create a location constraint. +so it may well be that one machine is more powerful than the other. + +In such cases, you may want to host the resources on the more powerful node +when it is available, to have the best performance -- or you may want to host +the resources on the _less_ powerful node when it's available, so you don't +have to worry about whether you can handle the load after a failover. + +To do this, we create a location constraint. In the location constraint below, we are saying the WebSite resource prefers the node pcmk-1 with a score of 50. Here, the score indicates -how badly we'd like the resource to run at this location. +how strongly we'd like the resource to run at this location. ----- [root@pcmk-1 ~]# pcs constraint location WebSite prefers pcmk-1=50 [root@pcmk-1 ~]# pcs constraint Location Constraints: Resource: WebSite Enabled on: pcmk-1 (score:50) Ordering Constraints: start ClusterIP then start WebSite (kind:Mandatory) Colocation Constraints: WebSite with ClusterIP (score:INFINITY) Ticket Constraints: [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-2 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 14:11:49 2018 -Last change: Fri Jan 12 14:11:20 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 17:21:41 2018 +Last change: Mon Sep 10 17:21:14 2018 by root via cibadmin on pcmk-1 2 nodes configured 2 resources configured Online: [ pcmk-1 pcmk-2 ] Full list of resources: - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 - WebSite (ocf::heartbeat:apache): Started pcmk-2 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + WebSite (ocf::heartbeat:apache): Started pcmk-2 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ----- Wait a minute, the resources are still on pcmk-2! Even though WebSite now prefers to run on pcmk-1, that preference is (intentionally) less than the resource stickiness (how much we preferred not to have unnecessary downtime). To see the current placement scores, you can use a tool called crm_simulate. ---- [root@pcmk-1 ~]# crm_simulate -sL Current cluster status: Online: [ pcmk-1 pcmk-2 ] - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 - WebSite (ocf::heartbeat:apache): Started pcmk-2 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + WebSite (ocf::heartbeat:apache): Started pcmk-2 Allocation scores: native_color: ClusterIP allocation score on pcmk-1: 50 native_color: ClusterIP allocation score on pcmk-2: 200 native_color: WebSite allocation score on pcmk-1: -INFINITY native_color: WebSite allocation score on pcmk-2: 100 Transition Summary: ---- == Move Resources Manually == There are always times when an administrator needs to override the cluster and force resources to move to a specific location. In this example, -we will force the WebSite to move to pcmk-1 by -updating our previous location constraint with a score of INFINITY. +we will force the WebSite to move to pcmk-1. + +We will use the *pcs resource move* command to create a temporary constraint +with a score of INFINITY. While we could update our existing constraint, +using *move* allows to easily get rid of the temporary constraint later. +If desired, we could even give a lifetime for the constraint, so it would +expire automatically -- but we don't that in this example. ----- -[root@pcmk-1 ~]# pcs constraint location WebSite prefers pcmk-1=INFINITY +[root@pcmk-1 ~]# pcs resource move WebSite pcmk-1 [root@pcmk-1 ~]# pcs constraint Location Constraints: Resource: WebSite - Enabled on: pcmk-1 (score:INFINITY) + Enabled on: pcmk-1 (score:50) + Enabled on: pcmk-1 (score:INFINITY) (role: Started) Ordering Constraints: start ClusterIP then start WebSite (kind:Mandatory) Colocation Constraints: WebSite with ClusterIP (score:INFINITY) Ticket Constraints: [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-2 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 14:19:34 2018 -Last change: Fri Jan 12 14:18:37 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 17:28:55 2018 +Last change: Mon Sep 10 17:28:27 2018 by root via crm_resource on pcmk-1 2 nodes configured 2 resources configured Online: [ pcmk-1 pcmk-2 ] Full list of resources: - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 - WebSite (ocf::heartbeat:apache): Started pcmk-1 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + WebSite (ocf::heartbeat:apache): Started pcmk-1 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ----- Once we've finished whatever activity required us to move the resources to pcmk-1 (in our case nothing), we can then allow the cluster -to resume normal operation by removing the new constraint. Since we previously -configured a default stickiness, the resources will remain on pcmk-1. +to resume normal operation by removing the new constraint. Due to our first +location constraint and our default stickiness, the resources will remain on +pcmk-1. -First, use the `--full` option to get the constraint's ID: +We will use the *pcs resource clear* command, which removes all temporary +constraints previously created by *pcs resource move* or *pcs resource ban*. ----- -[root@pcmk-1 ~]# pcs constraint --full -Location Constraints: - Resource: WebSite - Enabled on: pcmk-1 (score:INFINITY) (id:location-WebSite-pcmk-1-INFINITY) -Ordering Constraints: - start ClusterIP then start WebSite (kind:Mandatory) (id:order-ClusterIP-WebSite-mandatory) -Colocation Constraints: - WebSite with ClusterIP (score:INFINITY) (id:colocation-WebSite-ClusterIP-INFINITY) -Ticket Constraints: ------ - -Then remove the desired contraint using its ID: ------ -[root@pcmk-1 ~]# pcs constraint remove location-WebSite-pcmk-1-INFINITY +[root@pcmk-1 ~]# pcs resource clear WebSite [root@pcmk-1 ~]# pcs constraint Location Constraints: + Resource: WebSite + Enabled on: pcmk-1 (score:50) Ordering Constraints: start ClusterIP then start WebSite (kind:Mandatory) Colocation Constraints: WebSite with ClusterIP (score:INFINITY) Ticket Constraints: ----- -Note that the location constraint is now gone. If we check the cluster +Note that the INFINITY location constraint is now gone. If we check the cluster status, we can also see that (as expected) the resources are still active on pcmk-1. ----- -# pcs status +[root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-2 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 14:25:21 2018 -Last change: Fri Jan 12 14:24:29 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 17:31:47 2018 +Last change: Mon Sep 10 17:31:04 2018 by root via crm_resource on pcmk-1 2 nodes configured 2 resources configured Online: [ pcmk-1 pcmk-2 ] Full list of resources: - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 - WebSite (ocf::heartbeat:apache): Started pcmk-1 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + WebSite (ocf::heartbeat:apache): Started pcmk-1 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ----- + +To remove the constraint with the score of 50, we would first get the +constraint's ID using *pcs constraint --full*, then remove it with +*pcs constraint remove* and the ID. We won't show those steps here, +but feel free to try it on your own, with the help of the pcs man page +if necessary. diff --git a/doc/Clusters_from_Scratch/en-US/Ch-Installation.txt b/doc/Clusters_from_Scratch/en-US/Ch-Installation.txt index 98d8f93bed..af50405594 100644 --- a/doc/Clusters_from_Scratch/en-US/Ch-Installation.txt +++ b/doc/Clusters_from_Scratch/en-US/Ch-Installation.txt @@ -1,490 +1,514 @@ :compat-mode: legacy = Installation = == Install &DISTRO; &DISTRO_VERSION; == === Boot the Install Image === Download the 4GB -http://isoredirect.centos.org/centos/7/isos/x86_64/CentOS-7-x86_64-DVD-1708.iso[&DISTRO; +http://isoredirect.centos.org/centos/7/isos/x86_64/CentOS-7-x86_64-DVD-1804.iso[&DISTRO; &DISTRO_VERSION; DVD ISO]. Use the image to boot a virtual machine, or burn it to a DVD or USB drive and boot a physical server from that. After starting the installation, select your language and keyboard layout at the welcome screen. .&DISTRO; &DISTRO_VERSION; Installation Welcome Screen image::images/Welcome.png["Welcome to &DISTRO; &DISTRO_VERSION;",align="center",scaledwidth="100%"] === Installation Options === At this point, you get a chance to tweak the default installation options. .&DISTRO; &DISTRO_VERSION; Installation Summary Screen image::images/Installer.png["&DISTRO; &DISTRO_VERSION; Installation Summary",align="center",scaledwidth="100%"] Ignore the *SOFTWARE SELECTION* section (try saying that 10 times quickly). The *Infrastructure Server* environment does have add-ons with much of the software we need, but we will leave it as a *Minimal Install* here, so that we can see exactly what software is required later. === Configure Network === In the *NETWORK & HOSTNAME* section: - Edit *Host Name:* as desired. For this example, we will use *pcmk-1.localdomain*. - Select your network device, press *Configure...*, and manually assign a fixed IP address. For this example, we'll use 192.168.122.101 under *IPv4 Settings* (with an appropriate netmask, gateway and DNS server). -- Flip the switch to turn your network device on. +- Flip the switch to turn your network device on, and press *Done*. + +.&DISTRO; &DISTRO_VERSION; Network Interface Screen +image::images/Editing-eth0.png["&DISTRO; &DISTRO_VERSION; Editing eth0",align="center",scaledwidth="100%"] [IMPORTANT] =========== Do not accept the default network settings. Cluster machines should never obtain an IP address via DHCP, because DHCP's periodic address renewal will interfere with corosync. =========== === Configure Disk === By default, the installer's automatic partitioning will use LVM (which allows us to dynamically change the amount of space allocated to a given partition). However, it allocates all free space to the +/+ (aka. *root*) partition, which cannot be reduced in size later (dynamic increases are fine). In order to follow the DRBD and GFS2 portions of this guide, we need to reserve space on each machine for a replicated volume. Enter the *INSTALLATION DESTINATION* section, ensure the hard drive you want to install to is selected, select *I will configure partitioning*, and press *Done*. In the *MANUAL PARTITIONING* screen that comes next, click the option to create mountpoints automatically. Select the +/+ mountpoint, and reduce the desired capacity by 1GiB or so. Select *Modify...* by the volume group name, and change the *Size policy:* to *As large as possible*, to make the reclaimed space available inside the LVM volume group. We'll add the additional volume later. +.&DISTRO; &DISTRO_VERSION; Manual Partitioning Screen +image::images/Partitioning.png["&DISTRO; &DISTRO_VERSION; Partitioning",align="center",scaledwidth="100%"] + +Press *Done*, then *Accept changes*. + === Configure Time Synchronization === It is highly recommended to enable NTP on your cluster nodes. Doing so ensures all nodes agree on the current time and makes reading log files significantly easier. &DISTRO; will enable NTP automatically. If you want to change any time-related settings (such as time zone or NTP server), you can do this in the *TIME & DATE* section. === Finish Install === Select *Begin Installation*. Once it completes, set a root password, and reboot as instructed. For the purposes of this document, it is not necessary to create any additional users. After the node reboots, you'll see a login prompt on the console. Login using *root* and the password you created earlier. .&DISTRO; &DISTRO_VERSION; Console Prompt image::images/Console.png["&DISTRO; &DISTRO_VERSION; Console",align="center",scaledwidth="100%"] [NOTE] ====== From here on, we're going to be working exclusively from the terminal. ====== == Configure the OS == === Verify Networking === Ensure that the machine has the static IP address you configured earlier. ----- [root@pcmk-1 ~]# ip addr -1: lo: mtu 65536 qdisc noqueue state UNKNOWN +1: lo: mtu 65536 qdisc noqueue state UNKNOWN group default qlen 1000 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo - inet6 ::1/128 scope host valid_lft forever preferred_lft forever -2: eth0: mtu 1500 qdisc pfifo_fast state UP qlen 1000 - link/ether 52:54:00:d7:d6:08 brd ff:ff:ff:ff:ff:ff - inet 192.168.122.101/24 brd 192.168.122.255 scope global eth0 + inet6 ::1/128 scope host + valid_lft forever preferred_lft forever +2: eth0: mtu 1500 qdisc pfifo_fast state UP group default qlen 1000 + link/ether 52:54:00:8e:eb:41 brd ff:ff:ff:ff:ff:ff + inet 192.168.122.101/24 brd 192.168.122.255 scope global noprefixroute eth0 valid_lft forever preferred_lft forever - inet6 fe80::5054:ff:fed7:d608/64 scope link + inet6 fe80::e45:c99b:34c0:c657/64 scope link noprefixroute valid_lft forever preferred_lft forever ----- [NOTE] ===== If you ever need to change the node's IP address from the command line, follow these instructions, replacing *${device}* with the name of your network device: .... [root@pcmk-1 ~]# vi /etc/sysconfig/network-scripts/ifcfg-${device} # manually edit as desired [root@pcmk-1 ~]# nmcli dev disconnect ${device} [root@pcmk-1 ~]# nmcli con reload ${device} [root@pcmk-1 ~]# nmcli con up ${device} .... This makes *NetworkManager* aware that a change was made on the config file. ===== Next, ensure that the routes are as expected: ----- [root@pcmk-1 ~]# ip route -default via 192.168.122.1 dev eth0 proto static metric 100 -192.168.122.0/24 dev eth0 proto kernel scope link src 192.168.122.101 metric 100 +default via 192.168.122.1 dev eth0 proto static metric 100 +192.168.122.0/24 dev eth0 proto kernel scope link src 192.168.122.101 metric 100 ----- If there is no line beginning with *default via*, then you may need to add a line such as [source,Bash] GATEWAY="192.168.122.1" to the device configuration using the same process as described above for changing the IP address. Now, check for connectivity to the outside world. Start small by testing whether we can reach the gateway we configured. ----- [root@pcmk-1 ~]# ping -c 1 192.168.122.1 PING 192.168.122.1 (192.168.122.1) 56(84) bytes of data. -64 bytes from 192.168.122.1: icmp_req=1 ttl=64 time=0.249 ms +64 bytes from 192.168.122.1: icmp_seq=1 ttl=64 time=0.254 ms - --- 192.168.122.1 ping statistics --- +--- 192.168.122.1 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms -rtt min/avg/max/mdev = 0.249/0.249/0.249/0.000 ms +rtt min/avg/max/mdev = 0.254/0.254/0.254/0.000 ms ----- Now try something external; choose a location you know should be available. ----- -[root@pcmk-1 ~]# ping -c 1 www.google.com -PING www.l.google.com (173.194.72.106) 56(84) bytes of data. -64 bytes from tf-in-f106.1e100.net (173.194.72.106): icmp_req=1 ttl=41 time=167 ms +[root@pcmk-1 ~]# ping -c 1 www.clusterlabs.org +PING oss-uk-1.clusterlabs.org (109.74.197.241) 56(84) bytes of data. +64 bytes from oss-uk-1.clusterlabs.org (109.74.197.241): icmp_seq=1 ttl=49 time=333 ms - --- www.l.google.com ping statistics --- +--- oss-uk-1.clusterlabs.org ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms -rtt min/avg/max/mdev = 167.618/167.618/167.618/0.000 ms +rtt min/avg/max/mdev = 333.204/333.204/333.204/0.000 ms ----- === Login Remotely === The console isn't a very friendly place to work from, so we will now switch to accessing the machine remotely via SSH where we can use copy and paste, etc. From another host, check whether we can see the new host at all: ----- beekhof@f16 ~ # ping -c 1 192.168.122.101 PING 192.168.122.101 (192.168.122.101) 56(84) bytes of data. 64 bytes from 192.168.122.101: icmp_req=1 ttl=64 time=1.01 ms --- 192.168.122.101 ping statistics --- 1 packets transmitted, 1 received, 0% packet loss, time 0ms rtt min/avg/max/mdev = 1.012/1.012/1.012/0.000 ms ----- Next, login as root via SSH. ----- beekhof@f16 ~ # ssh -l root 192.168.122.101 The authenticity of host '192.168.122.101 (192.168.122.101)' can't be established. ECDSA key fingerprint is 6e:b7:8f:e2:4c:94:43:54:a8:53:cc:20:0f:29:a4:e0. Are you sure you want to continue connecting (yes/no)? yes Warning: Permanently added '192.168.122.101' (ECDSA) to the list of known hosts. root@192.168.122.101's password: Last login: Tue Aug 11 13:14:39 2015 [root@pcmk-1 ~]# ----- === Apply Updates === Apply any package updates released since your installation image was created: ---- [root@pcmk-1 ~]# yum update ---- === Use Short Node Names === During installation, we filled in the machine's fully qualified domain name (FQDN), which can be rather long when it appears in cluster logs and status output. See for yourself how the machine identifies itself: (((Nodes, short name))) ---- [root@pcmk-1 ~]# uname -n pcmk-1.localdomain ---- (((Nodes, Domain name (Query)))) We can use the `hostnamectl` tool to strip off the domain name: ---- [root@pcmk-1 ~]# hostnamectl set-hostname $(uname -n | sed s/\\..*//) ---- (((Nodes, Domain name (Remove from host name)))) Now, check that the machine is using the correct name: ---- [root@pcmk-1 ~]# uname -n pcmk-1 ---- +You may want to reboot to ensure all updates take effect. + == Repeat for Second Node == Repeat the Installation steps so far, so that you have two nodes ready to have the cluster software installed. For the purposes of this document, the additional node is called pcmk-2 with address 192.168.122.102. == Configure Communication Between Nodes == === Configure Host Name Resolution === Confirm that you can communicate between the two new nodes: ---- [root@pcmk-1 ~]# ping -c 3 192.168.122.102 PING 192.168.122.102 (192.168.122.102) 56(84) bytes of data. 64 bytes from 192.168.122.102: icmp_seq=1 ttl=64 time=0.343 ms 64 bytes from 192.168.122.102: icmp_seq=2 ttl=64 time=0.402 ms 64 bytes from 192.168.122.102: icmp_seq=3 ttl=64 time=0.558 ms --- 192.168.122.102 ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2000ms rtt min/avg/max/mdev = 0.343/0.434/0.558/0.092 ms ---- Now we need to make sure we can communicate with the machines by their name. If you have a DNS server, add additional entries for the two machines. Otherwise, you'll need to add the machines to +/etc/hosts+ on both nodes. Below are the entries for my cluster nodes: ---- [root@pcmk-1 ~]# grep pcmk /etc/hosts 192.168.122.101 pcmk-1.clusterlabs.org pcmk-1 192.168.122.102 pcmk-2.clusterlabs.org pcmk-2 ---- We can now verify the setup by again using ping: ---- [root@pcmk-1 ~]# ping -c 3 pcmk-2 PING pcmk-2.clusterlabs.org (192.168.122.101) 56(84) bytes of data. 64 bytes from pcmk-1.clusterlabs.org (192.168.122.101): icmp_seq=1 ttl=64 time=0.164 ms 64 bytes from pcmk-1.clusterlabs.org (192.168.122.101): icmp_seq=2 ttl=64 time=0.475 ms 64 bytes from pcmk-1.clusterlabs.org (192.168.122.101): icmp_seq=3 ttl=64 time=0.186 ms --- pcmk-2.clusterlabs.org ping statistics --- 3 packets transmitted, 3 received, 0% packet loss, time 2001ms rtt min/avg/max/mdev = 0.164/0.275/0.475/0.141 ms ---- === Configure SSH === SSH is a convenient and secure way to copy files and perform commands remotely. For the purposes of this guide, we will create a key without a password (using the -N option) so that we can perform remote actions without being prompted. (((SSH))) [WARNING] ========= Unprotected SSH keys (those without a password) are not recommended for servers exposed to the outside world. We use them here only to simplify the demo. ========= Create a new key and allow anyone with that key to log in: .Creating and Activating a new SSH Key ---- [root@pcmk-1 ~]# ssh-keygen -t dsa -f ~/.ssh/id_dsa -N "" Generating public/private dsa key pair. Your identification has been saved in /root/.ssh/id_dsa. Your public key has been saved in /root/.ssh/id_dsa.pub. The key fingerprint is: 91:09:5c:82:5a:6a:50:08:4e:b2:0c:62:de:cc:74:44 root@pcmk-1.clusterlabs.org The key's randomart image is: +--[ DSA 1024]----+ |==.ooEo.. | |X O + .o o | | * A + | | + . | | . S | | | | | | | | | +-----------------+ [root@pcmk-1 ~]# cp ~/.ssh/id_dsa.pub ~/.ssh/authorized_keys ---- (((Creating and Activating a new SSH Key))) Install the key on the other node: ---- [root@pcmk-1 ~]# scp -r ~/.ssh pcmk-2: The authenticity of host 'pcmk-2 (192.168.122.102)' can't be established. -ECDSA key fingerprint is a4:f5:b2:34:9d:86:2b:34:a2:87:37:b9:ca:68:52:ec. +ECDSA key fingerprint is SHA256:63xNPkPYq98rYznf3T9QYJAzlaGiAsSgFVNHOZjPWqc. +ECDSA key fingerprint is MD5:d9:bf:6e:32:88:be:47:3d:96:f1:96:27:65:05:0b:c3. Are you sure you want to continue connecting (yes/no)? yes Warning: Permanently added 'pcmk-2,192.168.122.102' (ECDSA) to the list of known hosts. root@pcmk-2's password: -id_dsa.pub 100% 616 0.6KB/s 00:00 -id_dsa 100% 672 0.7KB/s 00:00 -known_hosts 100% 400 0.4KB/s 00:00 -authorized_keys 100% 616 0.6KB/s 00:00 +id_dsa +id_dsa.pub +authorized_keys +known_hosts ---- Test that you can now run commands remotely, without being prompted: ---- [root@pcmk-1 ~]# ssh pcmk-2 -- uname -n pcmk-2 ---- == Install the Cluster Software == Fire up a shell on both nodes and run the following to install pacemaker, and while we're at it, some command-line tools to make our lives easier: ---- # yum install -y pacemaker pcs psmisc policycoreutils-python ---- [IMPORTANT] =========== This document will show commands that need to be executed on both nodes with a simple `#` prompt. Be sure to run them on each node individually. =========== [NOTE] =========== This document uses `pcs` for cluster management. Other alternatives, such as `crmsh`, are available, but their syntax will differ from the examples used here. =========== == Configure the Cluster Software == === Allow cluster services through firewall === On each node, allow cluster-related services through the local firewall: ---- # firewall-cmd --permanent --add-service=high-availability success # firewall-cmd --reload success ---- [NOTE] ====== If you are using iptables directly, or some other firewall solution besides firewalld, simply open the following ports, which can be used by various clustering components: TCP ports 2224, 3121, and 21064, and UDP port 5405. If you run into any problems during testing, you might want to disable the firewall and SELinux entirely until you have everything working. This may create significant security issues and should not be performed on machines that will be exposed to the outside world, but may be appropriate during development and testing on a protected host. To disable security measures: ---- [root@pcmk-1 ~]# setenforce 0 [root@pcmk-1 ~]# sed -i.bak "s/SELINUX=enforcing/SELINUX=permissive/g" /etc/selinux/config [root@pcmk-1 ~]# systemctl mask firewalld.service [root@pcmk-1 ~]# systemctl stop firewalld.service [root@pcmk-1 ~]# iptables --flush ---- ====== === Enable pcs Daemon === Before the cluster can be configured, the pcs daemon must be started and enabled to start at boot time on each node. This daemon works with the pcs command-line interface to manage synchronizing the corosync configuration across all nodes in the cluster. Start and enable the daemon by issuing the following commands on each node: ---- # systemctl start pcsd.service # systemctl enable pcsd.service -ln -s '/usr/lib/systemd/system/pcsd.service' '/etc/systemd/system/multi-user.target.wants/pcsd.service' +Created symlink from /etc/systemd/system/multi-user.target.wants/pcsd.service to /usr/lib/systemd/system/pcsd.service. ---- The installed packages will create a *hacluster* user with a disabled password. While this is fine for running `pcs` commands locally, the account needs a login password in order to perform such tasks as syncing the corosync configuration, or starting and stopping the cluster on other nodes. This tutorial will make use of such commands, so now we will set a password for the *hacluster* user, using the same password on both nodes: ---- # passwd hacluster Changing password for user hacluster. New password: Retype new password: passwd: all authentication tokens updated successfully. ---- [NOTE] =========== Alternatively, to script this process or set the password on a different machine from the one you're logged into, you can use the `--stdin` option for `passwd`: ---- [root@pcmk-1 ~]# ssh pcmk-2 -- 'echo mysupersecretpassword | passwd --stdin hacluster' ---- =========== === Configure Corosync === On either node, use `pcs cluster auth` to authenticate as the *hacluster* user: ---- [root@pcmk-1 ~]# pcs cluster auth pcmk-1 pcmk-2 Username: hacluster Password: -pcmk-1: Authorized pcmk-2: Authorized +pcmk-1: Authorized ---- Next, use `pcs cluster setup` on the same node to generate and synchronize the corosync configuration: ---- [root@pcmk-1 ~]# pcs cluster setup --name mycluster pcmk-1 pcmk-2 -Shutting down pacemaker/corosync services... -Redirecting to /bin/systemctl stop pacemaker.service -Redirecting to /bin/systemctl stop corosync.service -Killing any remaining services... -Removing all cluster configuration files... +Destroying cluster on nodes: pcmk-1, pcmk-2... +pcmk-2: Stopping Cluster (pacemaker)... +pcmk-1: Stopping Cluster (pacemaker)... +pcmk-1: Successfully destroyed cluster +pcmk-2: Successfully destroyed cluster + +Sending 'pacemaker_remote authkey' to 'pcmk-1', 'pcmk-2' +pcmk-2: successful distribution of the file 'pacemaker_remote authkey' +pcmk-1: successful distribution of the file 'pacemaker_remote authkey' +Sending cluster config files to the nodes... pcmk-1: Succeeded pcmk-2: Succeeded + +Synchronizing pcsd certificates on nodes pcmk-1, pcmk-2... +pcmk-2: Success +pcmk-1: Success +Restarting pcsd on the nodes in order to reload the certificates... +pcmk-2: Success +pcmk-1: Success ---- If you received an authorization error for either of those commands, make sure you configured the *hacluster* user account on each node with the same password. [NOTE] ====== If you are not using `pcs` for cluster administration, follow whatever procedures are appropriate for your tools to create a corosync.conf and copy it to all nodes. The `pcs` command will configure corosync to use UDP unicast transport; if you choose to use multicast instead, choose a multicast address carefully. footnote:[For some subtle issues, see http://web.archive.org/web/20101211210054/http://29west.com/docs/THPM/multicast-address-assignment.html[Topics in High-Performance Messaging: Multicast Address Assignment] or the more detailed treatment in https://www.cisco.com/c/dam/en/us/support/docs/ip/ip-multicast/ipmlt_wp.pdf[Cisco's Guidelines for Enterprise IP Multicast Address Allocation].] ====== The final corosync.conf configuration on each node should look something like the sample in <>. diff --git a/doc/Clusters_from_Scratch/en-US/Ch-Shared-Storage.txt b/doc/Clusters_from_Scratch/en-US/Ch-Shared-Storage.txt index 2481bad389..24eb26029f 100644 --- a/doc/Clusters_from_Scratch/en-US/Ch-Shared-Storage.txt +++ b/doc/Clusters_from_Scratch/en-US/Ch-Shared-Storage.txt @@ -1,530 +1,584 @@ :compat-mode: legacy = Replicate Storage Using DRBD = Even if you're serving up static websites, having to manually synchronize the contents of that website to all the machines in the cluster is not ideal. For dynamic websites, such as a wiki, it's not even an option. Not everyone care afford network-attached storage, but somehow the data needs to be kept in sync. Enter DRBD, which can be thought of as network-based RAID-1. footnote:[See http://www.drbd.org/ for details.] == Install the DRBD Packages == DRBD itself is included in the upstream kernel,footnote:[Since version 2.6.33] but we do need some utilities to use it effectively. CentOS does not ship these utilities, so we need to enable a third-party repository to get them. Supported packages for many OSes are available from DRBD's maker http://www.linbit.com/[LINBIT], but here we'll use the free http://elrepo.org/[ELRepo] repository. On both nodes, import the ELRepo package signing key, and enable the repository: ---- # rpm --import https://www.elrepo.org/RPM-GPG-KEY-elrepo.org # rpm -Uvh http://www.elrepo.org/elrepo-release-7.0-3.el7.elrepo.noarch.rpm +Retrieving http://www.elrepo.org/elrepo-release-7.0-3.el7.elrepo.noarch.rpm +Preparing... ################################# [100%] +Updating / installing... + 1:elrepo-release-7.0-3.el7.elrepo ################################# [100%] ---- Now, we can install the DRBD kernel module and utilities: ---- # yum install -y kmod-drbd84 drbd84-utils ---- DRBD will not be able to run under the default SELinux security policies. If you are familiar with SELinux, you can modify the policies in a more fine-grained manner, but here we will simply exempt DRBD processes from SELinux control: ---- # semanage permissive -a drbd_t ---- We will configure DRBD to use port 7789, so allow that port from each host to the other: ---- -[root@pcmk-1 ~]# firewall-cmd --permanent --add-rich-rule='rule family="ipv4" source address="192.168.122.102" port port="7789" protocol="tcp" accept' +[root@pcmk-1 ~]# firewall-cmd --permanent --add-rich-rule='rule family="ipv4" \ + source address="192.168.122.102" port port="7789" protocol="tcp" accept' success [root@pcmk-1 ~]# firewall-cmd --reload success ---- ---- -[root@pcmk-2 ~]# firewall-cmd --permanent --add-rich-rule='rule family="ipv4" source address="192.168.122.101" port port="7789" protocol="tcp" accept' +[root@pcmk-2 ~]# firewall-cmd --permanent --add-rich-rule='rule family="ipv4" \ + source address="192.168.122.101" port port="7789" protocol="tcp" accept' success [root@pcmk-2 ~]# firewall-cmd --reload success ---- [NOTE] ====== In this example, we have only two nodes, and all network traffic is on the same LAN. In production, it is recommended to use a dedicated, isolated network for cluster-related traffic, so the firewall configuration would likely be different; one approach would be to add the dedicated network interfaces to the trusted zone. ====== == Allocate a Disk Volume for DRBD == DRBD will need its own block device on each node. This can be a physical disk partition or logical volume, of whatever size -you need for your data. For this document, we will use a -1GiB logical volume, which is more than sufficient for a single HTML file and -(later) GFS2 metadata. +you need for your data. For this document, we will use a 512MiB logical volume, +which is more than sufficient for a single HTML file and (later) GFS2 metadata. ---- [root@pcmk-1 ~]# vgdisplay | grep -e Name -e Free VG Name centos_pcmk-1 - Free PE / Size 382 / 1.49 GiB -[root@pcmk-1 ~]# lvcreate --name drbd-demo --size 1G centos_pcmk-1 -Logical volume "drbd-demo" created + Free PE / Size 255 / 1020.00 MiB +[root@pcmk-1 ~]# lvcreate --name drbd-demo --size 512M centos_pcmk-1 + Logical volume "drbd-demo" created. [root@pcmk-1 ~]# lvs - LV VG Attr LSize Pool Origin Data% Meta% Move Log Cpy%Sync Convert - drbd-demo centos_pcmk-1 -wi-a----- 1.00g - root centos_pcmk-1 -wi-ao---- 5.00g - swap centos_pcmk-1 -wi-ao---- 1.00g + LV VG Attr LSize Pool Origin Data% Meta% Move Log Cpy%Sync Convert + drbd-demo centos_pcmk-1 -wi-a----- 512.00m + root centos_pcmk-1 -wi-ao---- 3.00g + swap centos_pcmk-1 -wi-ao---- 1.00g ---- Repeat for the second node, making sure to use the same size: ---- -[root@pcmk-1 ~]# ssh pcmk-2 -- lvcreate --name drbd-demo --size 1G centos_pcmk-2 -Logical volume "drbd-demo" created +[root@pcmk-1 ~]# ssh pcmk-2 -- lvcreate --name drbd-demo --size 512M centos_pcmk-2 + Logical volume "drbd-demo" created. ---- == Configure DRBD == There is no series of commands for building a DRBD configuration, so simply run this on both nodes to use this sample configuration: ---- # cat </etc/drbd.d/wwwdata.res resource wwwdata { protocol C; meta-disk internal; device /dev/drbd1; syncer { verify-alg sha1; } net { allow-two-primaries; } on pcmk-1 { disk /dev/centos_pcmk-1/drbd-demo; address 192.168.122.101:7789; } on pcmk-2 { disk /dev/centos_pcmk-2/drbd-demo; address 192.168.122.102:7789; } } END ---- [IMPORTANT] ========= Edit the file to use the hostnames, IP addresses and logical volume paths of your nodes if they differ from the ones used in this guide. ========= [NOTE] ======= Detailed information on the directives used in this configuration (and -other alternatives) is available at -http://www.drbd.org/users-guide/ch-configure.html - +other alternatives) is available in the +https://docs.linbit.com/docs/users-guide-8.4/#ch-configure[DRBD User's Guide]. The *allow-two-primaries* option would not normally be used in an active/passive cluster. We are adding it here for the convenience of changing to an active/active cluster later. ======= == Initialize DRBD == With the configuration in place, we can now get DRBD running. These commands create the local metadata for the DRBD resource, ensure the DRBD kernel module is loaded, and bring up the DRBD resource. Run them on one node: ---- [root@pcmk-1 ~]# drbdadm create-md wwwdata + + + + + + + + + + + + + + + + + + + + --== Thank you for participating in the global usage survey ==-- +The server's response is: + +you are the 2147th user to install this version initializing activity log -NOT initializing bitmap +initializing bitmap (16 KB) to all zero Writing meta data... New drbd meta data block successfully created. +success [root@pcmk-1 ~]# modprobe drbd [root@pcmk-1 ~]# drbdadm up wwwdata + + + + + + + + + + + + + + + + + + + --== Thank you for participating in the global usage survey ==-- +The server's response is: + ---- We can confirm DRBD's status on this node: ---- [root@pcmk-1 ~]# cat /proc/drbd -version: 8.4.6 (api:1/proto:86-101) -GIT-hash: 833d830e0152d1e457fa7856e71e11248ccf3f70 build by phil@Build64R7, 2015-04-10 05:13:52 +version: 8.4.11-1 (api:1/proto:86-101) +GIT-hash: 66145a308421e9c124ec391a7848ac20203bb03c build by mockbuild@, 2018-04-26 12:10:42 1: cs:WFConnection ro:Secondary/Unknown ds:Inconsistent/DUnknown C r----s - ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:1048508 + ns:0 nr:0 dw:0 dr:0 al:8 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:524236 ---- Because we have not yet initialized the data, this node's data is marked as *Inconsistent*. Because we have not yet initialized the second node, the local state is *WFConnection* (waiting for connection), and the partner node's status is marked as *Unknown*. -Now, repeat the above commands on the second node. This time, -when we check the status, it shows: +Now, repeat the above commands on the second node, starting with creating +wwwdata.res. After giving it time to connect, when we check the status, it +shows: ---- [root@pcmk-2 ~]# cat /proc/drbd -version: 8.4.6 (api:1/proto:86-101) -GIT-hash: 833d830e0152d1e457fa7856e71e11248ccf3f70 build by phil@Build64R7, 2015-04-10 05:13:52 +version: 8.4.11-1 (api:1/proto:86-101) +GIT-hash: 66145a308421e9c124ec391a7848ac20203bb03c build by mockbuild@, 2018-04-26 12:10:42 1: cs:Connected ro:Secondary/Secondary ds:Inconsistent/Inconsistent C r----- - ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:1048508 + ns:0 nr:0 dw:0 dr:0 al:8 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:524236 ---- You can see the state has changed to *Connected*, meaning the two DRBD nodes are communicating properly, and both nodes are in *Secondary* role with *Inconsistent* data. To make the data consistent, we need to tell DRBD which node should be considered to have the correct data. In this case, since we are creating a new resource, both have garbage, so we'll just pick pcmk-1 and run this command on it: ---- [root@pcmk-1 ~]# drbdadm primary --force wwwdata ---- [NOTE] ====== If you are using a different version of DRBD, the required syntax may be different. See the documentation for your version for how to perform these commands. ====== If we check the status immediately, we'll see something like this: ---- [root@pcmk-1 ~]# cat /proc/drbd -version: 8.4.6 (api:1/proto:86-101) -GIT-hash: 833d830e0152d1e457fa7856e71e11248ccf3f70 build by phil@Build64R7, 2015-04-10 05:13:52 +version: 8.4.11-1 (api:1/proto:86-101) +GIT-hash: 66145a308421e9c124ec391a7848ac20203bb03c build by mockbuild@, 2018-04-26 12:10:42 1: cs:SyncSource ro:Primary/Secondary ds:UpToDate/Inconsistent C r----- - ns:2872 nr:0 dw:0 dr:3784 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:1045636 - [>....................] sync'ed: 0.4% (1045636/1048508)K - finish: 0:10:53 speed: 1,436 (1,436) K/sec + ns:43184 nr:0 dw:0 dr:45312 al:8 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:481052 + [>...................] sync'ed: 8.6% (481052/524236)K + finish: 0:01:51 speed: 4,316 (4,316) K/sec ---- We can see that this node has the *Primary* role, the partner node has the *Secondary* role, this node's data is now considered *UpToDate*, the partner node's data is still *Inconsistent*, and a progress bar shows how far along the partner node is in synchronizing the data. After a while, the sync should finish, and you'll see something like: ---- [root@pcmk-1 ~]# cat /proc/drbd -version: 8.4.6 (api:1/proto:86-101) -GIT-hash: 833d830e0152d1e457fa7856e71e11248ccf3f70 build by phil@Build64R7, 2015-04-10 05:13:52 +version: 8.4.11-1 (api:1/proto:86-101) +GIT-hash: 66145a308421e9c124ec391a7848ac20203bb03c build by mockbuild@, 2018-04-26 12:10:42 1: cs:Connected ro:Primary/Secondary ds:UpToDate/UpToDate C r----- - ns:1048508 nr:0 dw:0 dr:1049420 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 + ns:524236 nr:0 dw:0 dr:526364 al:8 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:f oos:0 ---- Both sets of data are now *UpToDate*, and we can proceed to creating and populating a filesystem for our WebSite resource's documents. == Populate the DRBD Disk == On the node with the primary role (pcmk-1 in this example), create a filesystem on the DRBD device: ---- [root@pcmk-1 ~]# mkfs.xfs /dev/drbd1 -meta-data=/dev/drbd1 isize=256 agcount=4, agsize=65532 blks +meta-data=/dev/drbd1 isize=512 agcount=4, agsize=32765 blks = sectsz=512 attr=2, projid32bit=1 - = crc=0 finobt=0 -data = bsize=4096 blocks=262127, imaxpct=25 + = crc=1 finobt=0, sparse=0 +data = bsize=4096 blocks=131059, imaxpct=25 = sunit=0 swidth=0 blks -naming =version 2 bsize=4096 ascii-ci=0 ftype=0 -log =internal log bsize=4096 blocks=853, version=2 +naming =version 2 bsize=4096 ascii-ci=0 ftype=1 +log =internal log bsize=4096 blocks=855, version=2 = sectsz=512 sunit=0 blks, lazy-count=1 realtime =none extsz=4096 blocks=0, rtextents=0 ---- [NOTE] ==== In this example, we create an xfs filesystem with no special options. In a production environment, you should choose a filesystem type and options that are suitable for your application. ==== Mount the newly created filesystem, populate it with our web document, give it the same SELinux policy as the web document root, then unmount it (the cluster will handle mounting and unmounting it later): ---- [root@pcmk-1 ~]# mount /dev/drbd1 /mnt [root@pcmk-1 ~]# cat <<-END >/mnt/index.html My Test Site - DRBD END [root@pcmk-1 ~]# chcon -R --reference=/var/www/html /mnt [root@pcmk-1 ~]# umount /dev/drbd1 ---- == Configure the Cluster for the DRBD device == One handy feature `pcs` has is the ability to queue up several changes into a file and commit those changes all at once. To do this, start by populating the file with the current raw XML config from the CIB. ---- [root@pcmk-1 ~]# pcs cluster cib drbd_cfg ---- -Using the `pcs -f` option, make changes to the configuration saved +Using pcs's `-f` option, make changes to the configuration saved in the +drbd_cfg+ file. These changes will not be seen by the cluster until the +drbd_cfg+ file is pushed into the live cluster's CIB later. Here, we create a cluster resource for the DRBD device, and an additional _clone_ resource to allow the resource to run on both nodes at the same time. ---- [root@pcmk-1 ~]# pcs -f drbd_cfg resource create WebData ocf:linbit:drbd \ drbd_resource=wwwdata op monitor interval=60s [root@pcmk-1 ~]# pcs -f drbd_cfg resource master WebDataClone WebData \ master-max=1 master-node-max=1 clone-max=2 clone-node-max=1 \ notify=true [root@pcmk-1 ~]# pcs -f drbd_cfg resource show - ClusterIP (ocf::heartbeat:IPaddr2): Started - WebSite (ocf::heartbeat:apache): Started + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + WebSite (ocf::heartbeat:apache): Started pcmk-1 Master/Slave Set: WebDataClone [WebData] Stopped: [ pcmk-1 pcmk-2 ] ---- After you are satisfied with all the changes, you can commit them all at once by pushing the drbd_cfg file into the live CIB. ---- -[root@pcmk-1 ~]# pcs cluster cib-push drbd_cfg +[root@pcmk-1 ~]# pcs cluster cib-push drbd_cfg --config CIB updated ---- Let's see what the cluster did with the new configuration: ---- [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-1 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 09:29:41 2018 -Last change: Fri Jan 12 09:29:25 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 17:58:07 2018 +Last change: Mon Sep 10 17:57:53 2018 by root via cibadmin on pcmk-1 2 nodes configured 4 resources configured Online: [ pcmk-1 pcmk-2 ] Full list of resources: - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 - WebSite (ocf::heartbeat:apache): Started pcmk-1 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + WebSite (ocf::heartbeat:apache): Started pcmk-1 Master/Slave Set: WebDataClone [WebData] Masters: [ pcmk-1 ] Slaves: [ pcmk-2 ] Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ---- We can see that *WebDataClone* (our DRBD device) is running as master (DRBD's primary role) on *pcmk-1* and slave (DRBD's secondary role) on *pcmk-2*. [IMPORTANT] ==== The resource agent should load the DRBD module when needed if it's not already loaded. If that does not happen, configure your operating system to load the module at boot time. For &DISTRO; &DISTRO_VERSION;, you would run this on both nodes: ---- # echo drbd >/etc/modules-load.d/drbd.conf ---- ==== == Configure the Cluster for the Filesystem == Now that we have a working DRBD device, we need to mount its filesystem. In addition to defining the filesystem, we also need to tell the cluster where it can be located (only on the DRBD Primary) and when it is allowed to start (after the Primary was promoted). We are going to take a shortcut when creating the resource this time. Instead of explicitly saying we want the *ocf:heartbeat:Filesystem* script, we are only going to ask for *Filesystem*. We can do this because we know there is only one resource script named *Filesystem* available to pacemaker, and that pcs is smart enough to fill in the *ocf:heartbeat:* portion for us correctly in the configuration. If there were multiple *Filesystem* scripts from different OCF providers, we would need to specify the exact one we wanted. Once again, we will queue our changes to a file and then push the new configuration to the cluster as the final step. ---- [root@pcmk-1 ~]# pcs cluster cib fs_cfg [root@pcmk-1 ~]# pcs -f fs_cfg resource create WebFS Filesystem \ - device="/dev/drbd1" directory="/var/www/html" fstype="xfs" -[root@pcmk-1 ~]# pcs -f fs_cfg constraint colocation add WebFS with WebDataClone INFINITY with-rsc-role=Master -[root@pcmk-1 ~]# pcs -f fs_cfg constraint order promote WebDataClone then start WebFS + device="/dev/drbd1" directory="/var/www/html" fstype="xfs" +Assumed agent name 'ocf:heartbeat:Filesystem' (deduced from 'Filesystem') +[root@pcmk-1 ~]# pcs -f fs_cfg constraint colocation add \ + WebFS with WebDataClone INFINITY with-rsc-role=Master +[root@pcmk-1 ~]# pcs -f fs_cfg constraint order \ + promote WebDataClone then start WebFS Adding WebDataClone WebFS (kind: Mandatory) (Options: first-action=promote then-action=start) ---- We also need to tell the cluster that Apache needs to run on the same machine as the filesystem and that it must be active before Apache can start. ---- [root@pcmk-1 ~]# pcs -f fs_cfg constraint colocation add WebSite with WebFS INFINITY [root@pcmk-1 ~]# pcs -f fs_cfg constraint order WebFS then WebSite Adding WebFS WebSite (kind: Mandatory) (Options: first-action=start then-action=start) ---- Review the updated configuration. ---- [root@pcmk-1 ~]# pcs -f fs_cfg constraint Location Constraints: + Resource: WebSite + Enabled on: pcmk-1 (score:50) Ordering Constraints: start ClusterIP then start WebSite (kind:Mandatory) promote WebDataClone then start WebFS (kind:Mandatory) start WebFS then start WebSite (kind:Mandatory) Colocation Constraints: WebSite with ClusterIP (score:INFINITY) WebFS with WebDataClone (score:INFINITY) (with-rsc-role:Master) WebSite with WebFS (score:INFINITY) Ticket Constraints: ----- ----- [root@pcmk-1 ~]# pcs -f fs_cfg resource show - ClusterIP (ocf::heartbeat:IPaddr2): Started - WebSite (ocf::heartbeat:apache): Started + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + WebSite (ocf::heartbeat:apache): Started pcmk-1 Master/Slave Set: WebDataClone [WebData] Masters: [ pcmk-1 ] Slaves: [ pcmk-2 ] - WebFS (ocf::heartbeat:Filesystem): Stopped + WebFS (ocf::heartbeat:Filesystem): Stopped ---- After reviewing the new configuration, upload it and watch the cluster put it into effect. ---- -[root@pcmk-1 ~]# pcs cluster cib-push fs_cfg +[root@pcmk-1 ~]# pcs cluster cib-push fs_cfg --config +CIB updated [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-1 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 09:34:11 2018 -Last change: Fri Jan 12 09:34:09 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 18:02:24 2018 +Last change: Mon Sep 10 18:02:14 2018 by root via cibadmin on pcmk-1 2 nodes configured 5 resources configured Online: [ pcmk-1 pcmk-2 ] Full list of resources: - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 - WebSite (ocf::heartbeat:apache): Started pcmk-1 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-1 + WebSite (ocf::heartbeat:apache): Started pcmk-1 Master/Slave Set: WebDataClone [WebData] Masters: [ pcmk-1 ] Slaves: [ pcmk-2 ] - WebFS (ocf::heartbeat:Filesystem): Started pcmk-1 + WebFS (ocf::heartbeat:Filesystem): Started pcmk-1 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ---- == Test Cluster Failover == Previously, we used `pcs cluster stop pcmk-1` to stop all cluster services on *pcmk-1*, failing over the cluster resources, but there is another way to safely simulate node failure. We can put the node into _standby mode_. Nodes in this state continue to run corosync and pacemaker but are not allowed to run resources. Any resources found active there will be moved elsewhere. This feature can be particularly useful when performing system administration tasks such as updating packages used by cluster resources. Put the active node into standby mode, and observe the cluster move all -the resources to the other node. The node's status will -change to indicate that it can no longer host resources. +the resources to the other node. The node's status will change to indicate that +it can no longer host resources, and eventually all the resources will move. ---- [root@pcmk-1 ~]# pcs cluster standby pcmk-1 [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-1 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 09:36:49 2018 -Last change: Fri Jan 12 09:36:43 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 18:04:22 2018 +Last change: Mon Sep 10 18:03:43 2018 by root via cibadmin on pcmk-1 2 nodes configured 5 resources configured -Node pcmk-1 (1): standby +Node pcmk-1: standby Online: [ pcmk-2 ] Full list of resources: - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 - WebSite (ocf::heartbeat:apache): Started pcmk-2 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + WebSite (ocf::heartbeat:apache): Started pcmk-2 Master/Slave Set: WebDataClone [WebData] Masters: [ pcmk-2 ] Stopped: [ pcmk-1 ] - WebFS (ocf::heartbeat:Filesystem): Started pcmk-2 + WebFS (ocf::heartbeat:Filesystem): Started pcmk-2 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ---- Once we've done everything we needed to on pcmk-1 (in this case nothing, we just wanted to see the resources move), we can allow the node to be a full cluster member again. ---- [root@pcmk-1 ~]# pcs cluster unstandby pcmk-1 [root@pcmk-1 ~]# pcs status Cluster name: mycluster Stack: corosync -Current DC: pcmk-1 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 09:38:02 2018 -Last change: Fri Jan 12 09:37:56 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 18:05:22 2018 +Last change: Mon Sep 10 18:05:21 2018 by root via cibadmin on pcmk-1 2 nodes configured 5 resources configured Online: [ pcmk-1 pcmk-2 ] Full list of resources: - ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 - WebSite (ocf::heartbeat:apache): Started pcmk-2 + ClusterIP (ocf::heartbeat:IPaddr2): Started pcmk-2 + WebSite (ocf::heartbeat:apache): Started pcmk-2 Master/Slave Set: WebDataClone [WebData] Masters: [ pcmk-2 ] Slaves: [ pcmk-1 ] - WebFS (ocf::heartbeat:Filesystem): Started pcmk-2 + WebFS (ocf::heartbeat:Filesystem): Started pcmk-2 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ---- Notice that *pcmk-1* is back to the *Online* state, and that the cluster resources stay where they are due to our resource stickiness settings configured earlier. diff --git a/doc/Clusters_from_Scratch/en-US/Ch-Stonith.txt b/doc/Clusters_from_Scratch/en-US/Ch-Stonith.txt index 51eb5a1a1a..e25735440f 100644 --- a/doc/Clusters_from_Scratch/en-US/Ch-Stonith.txt +++ b/doc/Clusters_from_Scratch/en-US/Ch-Stonith.txt @@ -1,166 +1,170 @@ :compat-mode: legacy = Configure STONITH = == What is STONITH? == STONITH (Shoot The Other Node In The Head aka. fencing) protects your data from being corrupted by rogue nodes or unintended concurrent access. Just because a node is unresponsive doesn't mean it has stopped accessing your data. The only way to be 100% sure that your data is safe, is to use STONITH to ensure that the node is truly offline before allowing the data to be accessed from another node. STONITH also has a role to play in the event that a clustered service cannot be stopped. In this case, the cluster uses STONITH to force the whole node offline, thereby making it safe to start the service elsewhere. == Choose a STONITH Device == It is crucial that your STONITH device can allow the cluster to differentiate between a node failure and a network failure. A common mistake people make when choosing a STONITH device is to use a remote power switch (such as many on-board IPMI controllers) that shares power with the node it controls. If the power fails in such a case, the cluster cannot be sure whether the node is really offline, or active and suffering from a network fault, so the cluster will stop all resources to avoid a possible split-brain situation. Likewise, any device that relies on the machine being active (such as SSH-based "devices" sometimes used during testing) is inappropriate. == Configure the Cluster for STONITH == . Install the STONITH agent(s). To see what packages are available, run `yum search fence-`. Be sure to install the package(s) on all cluster nodes. . Configure the STONITH device itself to be able to fence your nodes and accept fencing requests. This includes any necessary configuration on the device and on the nodes, and any firewall or SELinux changes needed. Test the communication between the device and your nodes. . Find the correct STONITH agent script: `pcs stonith list` . Find the parameters associated with the device: +pcs stonith describe pass:[agent_name]+ . Create a local copy of the CIB: `pcs cluster cib stonith_cfg` . Create the fencing resource: +pcs -f stonith_cfg stonith create pass:[stonith_id stonith_device_type [stonith_device_options]]+ + Any flags that do not take arguments, such as +--ssl+, should be passed as +ssl=1+. . Enable STONITH in the cluster: `pcs -f stonith_cfg property set stonith-enabled=true` . If the device does not know how to fence nodes based on their uname, you may also need to set the special *pcmk_host_map* parameter. See `man pacemaker-fenced` for details. . If the device does not support the *list* command, you may also need to set the special *pcmk_host_list* and/or *pcmk_host_check* parameters. See `man pacemaker-fenced` for details. . If the device does not expect the victim to be specified with the *port* parameter, you may also need to set the special *pcmk_host_argument* parameter. See `man pacemaker-fenced` for details. . Commit the new configuration: `pcs cluster cib-push stonith_cfg` . Once the STONITH resource is running, test it (you might want to stop the cluster on that machine first): +stonith_admin --reboot pass:[nodename]+ == Example == For this example, assume we have a chassis containing four nodes and an IPMI device active on 10.0.0.1. Following the steps above would go something like this: Step 1: Install the *fence-agents-ipmilan* package on both nodes. Step 2: Configure the IP address, authentication credentials, etc. in the IPMI device itself. Step 3: Choose the *fence_ipmilan* STONITH agent. Step 4: Obtain the agent's possible parameters: ---- [root@pcmk-1 ~]# pcs stonith describe fence_ipmilan fence_ipmilan - Fence agent for IPMI fence_ipmilan is an I/O Fencing agentwhich can be used with machines controlled by IPMI.This agent calls support software ipmitool (http://ipmitool.sf.net/). WARNING! This fence agent might report success before the node is powered off. You should use -m/method onoff if your fence device works correctly with that option. Stonith options: ipport: TCP/UDP port to use for connection with device + hexadecimal_kg: Hexadecimal-encoded Kg key for IPMIv2 authentication port: IP address or hostname of fencing device (together with --port-as-ip) inet6_only: Forces agent to use IPv6 addresses only ipaddr: IP Address or Hostname passwd_script: Script to retrieve password method: Method to fence (onoff|cycle) inet4_only: Forces agent to use IPv4 addresses only passwd: Login password or passphrase lanplus: Use Lanplus to improve security of connection auth: IPMI Lan Auth type. - action: Fencing Action WARNING: specifying 'action' is deprecated and not necessary with current Pacemaker versions. cipher: Ciphersuite to use (same as ipmitool -C parameter) target: Bridge IPMI requests to the remote target address privlvl: Privilege level on IPMI device timeout: Timeout (sec) for IPMI operation login: Login Name + verbose: Verbose mode + debug: Write debug information to given file power_wait: Wait X seconds after issuing ON/OFF login_timeout: Wait X seconds for cmd prompt after login delay: Wait X seconds before fencing is started power_timeout: Test X seconds for status change after ON/OFF ipmitool_path: Path to ipmitool binary shell_timeout: Wait X seconds for cmd prompt after issuing command port_as_ip: Make "port/plug" to be an alias to IP address retry_on: Count of attempts to retry power on sudo: Use sudo (without password) when calling 3rd party sotfware. priority: The priority of the stonith resource. Devices are tried in order of highest priority to lowest. - pcmk_host_map: A mapping of host names to ports numbers for devices that do not support host names. Eg. node1:1;node2:2,3 would tell the cluster to use port 1 for node1 and ports - 2 and 3 for node2 + pcmk_host_map: A mapping of host names to ports numbers for devices that do not support host names. Eg. node1:1;node2:2,3 would tell the cluster to use port 1 for node1 and ports 2 and + 3 for node2 pcmk_host_list: A list of machines controlled by this device (Optional unless pcmk_host_check=static-list). - pcmk_host_check: How to determine which machines are controlled by the device. Allowed values: dynamic-list (query the device), static-list (check the pcmk_host_list attribute), - none (assume every device can fence every machine) - pcmk_delay_max: Enable random delay for stonith actions and specify the maximum of random delay This prevents double fencing when using slow devices such as sbd. Use this to - enable random delay for stonith actions and specify the maximum of random delay. - pcmk_action_limit: The maximum number of actions can be performed in parallel on this device Cluster property concurrent-fencing=true needs to be configured first. Then use this - to specify the maximum number of actions can be performed in parallel on this device. -1 is unlimited. + pcmk_host_check: How to determine which machines are controlled by the device. Allowed values: dynamic-list (query the device), static-list (check the pcmk_host_list attribute), none + (assume every device can fence every machine) + pcmk_delay_max: Enable a random delay for stonith actions and specify the maximum of random delay. This prevents double fencing when using slow devices such as sbd. Use this to enable a + random delay for stonith actions. The overall delay is derived from this random delay value adding a static delay so that the sum is kept below the maximum delay. + pcmk_delay_base: Enable a base delay for stonith actions and specify base delay value. This prevents double fencing when different delays are configured on the nodes. Use this to enable + a static delay for stonith actions. The overall delay is derived from a random delay value adding this static delay so that the sum is kept below the maximum delay. + pcmk_action_limit: The maximum number of actions can be performed in parallel on this device Pengine property concurrent-fencing=true needs to be configured first. Then use this to + specify the maximum number of actions can be performed in parallel on this device. -1 is unlimited. Default operations: monitor: interval=60s ---- Step 5: `pcs cluster cib stonith_cfg` Step 6: Here are example parameters for creating our STONITH resource: ---- [root@pcmk-1 ~]# pcs -f stonith_cfg stonith create ipmi-fencing fence_ipmilan \ pcmk_host_list="pcmk-1 pcmk-2" ipaddr=10.0.0.1 login=testuser \ passwd=acd123 op monitor interval=60s [root@pcmk-1 ~]# pcs -f stonith_cfg stonith ipmi-fencing (stonith:fence_ipmilan): Stopped ---- Steps 7-10: Enable STONITH in the cluster: ---- [root@pcmk-1 ~]# pcs -f stonith_cfg property set stonith-enabled=true [root@pcmk-1 ~]# pcs -f stonith_cfg property Cluster Properties: cluster-infrastructure: corosync cluster-name: mycluster - dc-version: 1.1.16-12.el7_4.5-94ff4df + dc-version: 1.1.18-11.el7_5.3-2b07d5c5a9 have-watchdog: false stonith-enabled: true ---- -Step 11: `pcs cluster cib-push stonith_cfg` +Step 11: `pcs cluster cib-push stonith_cfg --config` Step 12: Test: ---- [root@pcmk-1 ~]# pcs cluster stop pcmk-2 [root@pcmk-1 ~]# stonith_admin --reboot pcmk-2 ---- After a successful test, login to any rebooted nodes, and start the cluster (with `pcs cluster start`). diff --git a/doc/Clusters_from_Scratch/en-US/Ch-Tools.txt b/doc/Clusters_from_Scratch/en-US/Ch-Tools.txt index c396c0010f..1beaef9c87 100644 --- a/doc/Clusters_from_Scratch/en-US/Ch-Tools.txt +++ b/doc/Clusters_from_Scratch/en-US/Ch-Tools.txt @@ -1,132 +1,131 @@ :compat-mode: legacy = Pacemaker Tools = == Simplify administration using a cluster shell == In the dark past, configuring Pacemaker required the administrator to read and write XML. In true UNIX style, there were also a number of different commands that specialized in different aspects of querying and updating the cluster. All of that has been greatly simplified with the creation of unified command-line shells (and GUIs) that hide all the messy XML scaffolding. These shells take all the individual aspects required for managing and configuring a cluster, and pack them into one simple-to-use command line tool. They even allow you to queue up several changes at once and commit them all at once. -Two popular command-line shells are `pcs` and -`crmsh`. This edition of Clusters from Scratch is based on `pcs`. - -[NOTE] -=========== -The two shells share many concepts but the scope, layout and syntax -does differ, so make sure you read the version of this guide that -corresponds to the software installed on your system. -=========== +Two popular command-line shells are `pcs` and `crmsh`. Clusters from Scratch is +based on `pcs` because it comes with CentOS, but both have similar +functionality. Choosing a shell or GUI is a matter of personal preference and +what comes with (and perhaps is supported by) your choice of operating system. == Explore pcs == Start by taking some time to familiarize yourself with what `pcs` can do. ---- [root@pcmk-1 ~]# pcs Usage: pcs [-f file] [-h] [commands]... Control and configure pacemaker and corosync. Options: -h, --help Display usage and exit. -f file Perform actions on file instead of active CIB. --debug Print all network traffic and external commands run. - --version Print pcs version information. + --version Print pcs version information. List pcs capabilities if + --full is specified. --request-timeout Timeout for each outgoing request to another node in seconds. Default is 60s. + --force Override checks and errors, the exact behavior depends on + the command. WARNING: Using the --force option is + strongly discouraged unless you know what you are doing. Commands: cluster Configure cluster options and nodes. resource Manage cluster resources. stonith Manage fence devices. constraint Manage resource constraints. property Manage pacemaker properties. acl Manage pacemaker access control lists. qdevice Manage quorum device provider on the local host. quorum Manage cluster quorum settings. booth Manage booth (cluster ticket manager). status View cluster status. config View and manage cluster configuration. pcsd Manage pcs daemon. node Manage cluster nodes. alert Manage pacemaker alerts. ---- As you can see, the different aspects of cluster management are separated into categories. To discover the functionality available in each of these categories, one can issue the command +pcs pass:[category] help+. Below is an example of all the options available under the status category. ---- [root@pcmk-1 ~]# pcs status help Usage: pcs status [commands]... View current cluster and resource status Commands: [status] [--full | --hide-inactive] View all information about the cluster and resources (--full provides more details, --hide-inactive hides inactive resources). resources [ | --full | --groups | --hide-inactive] Show all currently configured resources or if a resource is specified show the options for the configured resource. If --full is specified, all configured resource options will be displayed. If --groups is specified, only show groups (and their resources). If --hide-inactive is specified, only show active resources. groups View currently configured groups and their resources. cluster View current cluster status. corosync View current membership information as seen by corosync. quorum View current quorum status. qdevice [--full] [] Show runtime status of specified model of quorum device provider. Using --full will give more detailed output. If is specified, only information about the specified cluster will be displayed. nodes [corosync | both | config] View current status of nodes from pacemaker. If 'corosync' is specified, view current status of nodes from corosync instead. If 'both' is specified, view current status of nodes from both corosync & pacemaker. If 'config' is specified, print nodes from corosync & pacemaker configuration. pcsd []... Show current status of pcsd on nodes specified, or on all nodes configured in the local cluster if no nodes are specified. xml View xml version of status (output from crm_mon -r -1 -X). ---- Additionally, if you are interested in the version and supported cluster stack(s) available with your Pacemaker installation, run: ---- [root@pcmk-1 ~]# pacemakerd --features -Pacemaker 1.1.16-12.el7_4.5 (Build: 94ff4df) - Supporting v3.0.12: generated-manpages agent-manpages ncurses libqb-logging libqb-ipc systemd nagios corosync-native atomic-attrd acls +Pacemaker 1.1.18-11.el7_5.3 (Build: 2b07d5c5a9) + Supporting v3.0.14: generated-manpages agent-manpages ncurses libqb-logging libqb-ipc systemd nagios corosync-native atomic-attrd acls ---- diff --git a/doc/Clusters_from_Scratch/en-US/Ch-Verification.txt b/doc/Clusters_from_Scratch/en-US/Ch-Verification.txt index 19fcdf172e..d4762e34fa 100644 --- a/doc/Clusters_from_Scratch/en-US/Ch-Verification.txt +++ b/doc/Clusters_from_Scratch/en-US/Ch-Verification.txt @@ -1,148 +1,151 @@ :compat-mode: legacy = Start and Verify Cluster = == Start the Cluster == Now that corosync is configured, it is time to start the cluster. The command below will start corosync and pacemaker on both nodes in the cluster. If you are issuing the start command from a different node than the one you ran the `pcs cluster auth` command on earlier, you must authenticate on the current node you are logged into before you will be allowed to start the cluster. ---- [root@pcmk-1 ~]# pcs cluster start --all pcmk-1: Starting Cluster... pcmk-2: Starting Cluster... ---- [NOTE] ====== An alternative to using the `pcs cluster start --all` command is to issue either of the below command sequences on each node in the cluster separately: ---- # pcs cluster start Starting Cluster... ---- or ---- # systemctl start corosync.service # systemctl start pacemaker.service ---- ====== [IMPORTANT] ==== In this example, we are not enabling the corosync and pacemaker services to start at boot. If a cluster node fails or is rebooted, you will need to run +pcs cluster start pass:[nodename]+ (or `--all`) to start the cluster on it. While you could enable the services to start at boot, requiring a manual start of cluster services gives you the opportunity to do a post-mortem investigation of a node failure before returning it to the cluster. ==== == Verify Corosync Installation == First, use `corosync-cfgtool` to check whether cluster communication is happy: ---- [root@pcmk-1 ~]# corosync-cfgtool -s Printing ring status. Local node ID 1 RING ID 0 id = 192.168.122.101 status = ring 0 active with no faults ---- We can see here that everything appears normal with our fixed IP address (not a 127.0.0.x loopback address) listed as the *id*, and *no faults* for the status. If you see something different, you might want to start by checking -the node's network, firewall and selinux configurations. +the node's network, firewall and SELinux configurations. Next, check the membership and quorum APIs: ---- -[root@pcmk-1 ~]# corosync-cmapctl | grep members +[root@pcmk-1 ~]# corosync-cmapctl | grep members runtime.totem.pg.mrp.srp.members.1.config_version (u64) = 0 runtime.totem.pg.mrp.srp.members.1.ip (str) = r(0) ip(192.168.122.101) runtime.totem.pg.mrp.srp.members.1.join_count (u32) = 1 runtime.totem.pg.mrp.srp.members.1.status (str) = joined runtime.totem.pg.mrp.srp.members.2.config_version (u64) = 0 runtime.totem.pg.mrp.srp.members.2.ip (str) = r(0) ip(192.168.122.102) -runtime.totem.pg.mrp.srp.members.2.join_count (u32) = 2 +runtime.totem.pg.mrp.srp.members.2.join_count (u32) = 1 runtime.totem.pg.mrp.srp.members.2.status (str) = joined [root@pcmk-1 ~]# pcs status corosync + Membership information - -------------------------- +\---------------------- Nodeid Votes Name 1 1 pcmk-1 (local) 2 1 pcmk-2 ---- You should see both nodes have joined the cluster. == Verify Pacemaker Installation == Now that we have confirmed that Corosync is functional, we can check the rest of the stack. Pacemaker has already been started, so verify the necessary processes are running: ---- [root@pcmk-1 ~]# ps axf PID TTY STAT TIME COMMAND 2 ? S 0:00 [kthreadd] ...lots of processes... - 1362 ? Ssl 0:35 corosync - 1379 ? Ss 0:00 /usr/sbin/pacemakerd -f - 1380 ? Ss 0:00 \_ /usr/libexec/pacemaker/pacemaker-based - 1381 ? Ss 0:00 \_ /usr/libexec/pacemaker/pacemaker-fenced - 1382 ? Ss 0:00 \_ /usr/libexec/pacemaker/pacemaker-execd - 1383 ? Ss 0:00 \_ /usr/libexec/pacemaker/pacemaker-attrd - 1384 ? Ss 0:00 \_ /usr/libexec/pacemaker/pacemaker-schedulerd - 1385 ? Ss 0:00 \_ /usr/libexec/pacemaker/pacemaker-controld +11635 ? SLsl 0:03 corosync +11642 ? Ss 0:00 /usr/sbin/pacemakerd -f +11643 ? Ss 0:00 \_ /usr/libexec/pacemaker/cib +11644 ? Ss 0:00 \_ /usr/libexec/pacemaker/stonithd +11645 ? Ss 0:00 \_ /usr/libexec/pacemaker/lrmd +11646 ? Ss 0:00 \_ /usr/libexec/pacemaker/attrd +11647 ? Ss 0:00 \_ /usr/libexec/pacemaker/pengine +11648 ? Ss 0:00 \_ /usr/libexec/pacemaker/crmd ---- If that looks OK, check the `pcs status` output: ---- [root@pcmk-1 ~]# pcs status Cluster name: mycluster WARNING: no stonith devices and stonith-enabled is not false Stack: corosync -Current DC: pcmk-2 (version 1.1.16-12.el7_4.5-94ff4df) - partition with quorum -Last updated: Fri Jan 12 16:15:29 2018 -Last change: Fri Jan 12 15:49:47 2018 +Current DC: pcmk-2 (version 1.1.18-11.el7_5.3-2b07d5c5a9) - partition with quorum +Last updated: Mon Sep 10 16:37:34 2018 +Last change: Mon Sep 10 16:30:53 2018 by hacluster via crmd on pcmk-2 2 nodes configured 0 resources configured Online: [ pcmk-1 pcmk-2 ] -No active resources +No resources + Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled ---- -Finally, ensure there are no startup errors (aside from messages relating -to not having STONITH configured, which are OK at this point): +Finally, ensure there are no start-up errors from corosync or pacemaker (aside +from messages relating to not having STONITH configured, which are OK at this +point): ---- -[root@pcmk-1 ~]# journalctl | grep -i error +[root@pcmk-1 ~]# journalctl -b | grep -i error ---- [NOTE] ====== Other operating systems may report startup errors in other locations, for example +/var/log/messages+. ====== Repeat these checks on the other node. The results should be the same. diff --git a/doc/Clusters_from_Scratch/en-US/Clusters_from_Scratch.ent b/doc/Clusters_from_Scratch/en-US/Clusters_from_Scratch.ent index 85bc1dba45..4413d22505 100644 --- a/doc/Clusters_from_Scratch/en-US/Clusters_from_Scratch.ent +++ b/doc/Clusters_from_Scratch/en-US/Clusters_from_Scratch.ent @@ -1,6 +1,6 @@ - + diff --git a/doc/Clusters_from_Scratch/en-US/Revision_History.xml b/doc/Clusters_from_Scratch/en-US/Revision_History.xml index d0eb49728e..537b31e9da 100644 --- a/doc/Clusters_from_Scratch/en-US/Revision_History.xml +++ b/doc/Clusters_from_Scratch/en-US/Revision_History.xml @@ -1,79 +1,85 @@ %BOOK_ENTITIES; ]> Revision History 1-0 Mon May 17 2010 AndrewBeekhofandrew@beekhof.net Import from Pages.app 2-0 Wed Sep 22 2010 RaoulScarazzinirasca@miamammausalinux.org Italian translation 3-0 Wed Feb 9 2011 AndrewBeekhofandrew@beekhof.net Updated for Fedora 13 4-0 Wed Oct 5 2011 AndrewBeekhofandrew@beekhof.net Update the GFS2 section to use CMAN 5-0 Fri Feb 10 2012 AndrewBeekhofandrew@beekhof.net Generate docbook content from asciidoc sources 6-0 Tues July 3 2012 AndrewBeekhofandrew@beekhof.net Updated for Fedora 17 7-0 Fri Sept 14 2012 DavidVosseldavidvossel@gmail.com Updated for pcs 8-0 Mon Jan 05 2015 KenGaillotkgaillot@redhat.com Updated for Fedora 21 8-1 Thu Jan 08 2015 KenGaillotkgaillot@redhat.com Minor corrections, plus use include file for intro 9-0 Fri Aug 14 2015 KenGaillotkgaillot@redhat.com Update for CentOS 7.1 and leaving firewalld/SELinux enabled 10-0 Fri Jan 12 2018 KenGaillotkgaillot@redhat.com Update banner for Pacemaker 2.0 and content for CentOS 7.4 with Pacemaker 1.1.16 + + 10-1 + Wed Sep 5 2018 + KenGaillotkgaillot@redhat.com + Update for CentOS 7.5 with Pacemaker 1.1.18 + diff --git a/doc/shared/en-US/images/Console.png b/doc/shared/en-US/images/Console.png index 6d61b6df80..27529de0bb 100644 Binary files a/doc/shared/en-US/images/Console.png and b/doc/shared/en-US/images/Console.png differ diff --git a/doc/shared/en-US/images/Installer.png b/doc/shared/en-US/images/Installer.png index 9f7a0d33bc..fb35f1c849 100644 Binary files a/doc/shared/en-US/images/Installer.png and b/doc/shared/en-US/images/Installer.png differ diff --git a/doc/shared/en-US/images/Welcome.png b/doc/shared/en-US/images/Welcome.png index 20c6f1c517..f44ba434d3 100644 Binary files a/doc/shared/en-US/images/Welcome.png and b/doc/shared/en-US/images/Welcome.png differ