diff --git a/doc/sphinx/Clusters_from_Scratch/active-passive.rst b/doc/sphinx/Clusters_from_Scratch/active-passive.rst index a4c6801333..1699c43377 100644 --- a/doc/sphinx/Clusters_from_Scratch/active-passive.rst +++ b/doc/sphinx/Clusters_from_Scratch/active-passive.rst @@ -1,324 +1,324 @@ Create an Active/Passive Cluster -------------------------------- .. index:: pair: resource; IP address Add a Resource ############## Our first resource will be a floating IP address that the cluster can bring up on either node. Regardless of where any cluster service(s) are running, end users need to be able to communicate with them at a consistent address. Here, we will use ``192.168.122.120`` as the floating IP address, give it the imaginative name ``ClusterIP``, and tell the cluster to check whether it is still running every 30 seconds. .. WARNING:: The chosen address must not already be in use on the network, on a cluster node or elsewhere. Do not reuse an IP address one of the nodes already has configured. .. code-block:: console [root@pcmk-1 ~]# pcs resource create ClusterIP ocf:heartbeat:IPaddr2 \ ip=192.168.122.120 cidr_netmask=24 op monitor interval=30s Another important piece of information here is ``ocf:heartbeat:IPaddr2``. This tells Pacemaker three things about the resource you want to add: * The first field (``ocf`` in this case) is the standard to which the resource agent conforms and where to find it. * The second field (``heartbeat`` in this case) is known as the provider. Currently, this field is supported only for OCF resources. It tells Pacemaker which OCF namespace the resource script is in. * The third field (``IPaddr2`` in this case) is the name of the resource agent, the executable file responsible for starting, stopping, monitoring, and possibly promoting and demoting the resource. To obtain a list of the available resource standards (the ``ocf`` part of ``ocf:heartbeat:IPaddr2``), run: .. code-block:: console [root@pcmk-1 ~]# pcs resource standards lsb ocf service systemd To obtain a list of the available OCF resource providers (the ``heartbeat`` part of ``ocf:heartbeat:IPaddr2``), run: .. code-block:: console [root@pcmk-1 ~]# pcs resource providers heartbeat openstack pacemaker Finally, if you want to see all the resource agents available for a specific OCF provider (the ``IPaddr2`` part of ``ocf:heartbeat:IPaddr2``), run: .. code-block:: console [root@pcmk-1 ~]# pcs resource agents ocf:heartbeat apache conntrackd corosync-qnetd . . (skipping lots of resources to save space) . VirtualDomain Xinetd If you want to list all resource agents available on the system, run ``pcs resource list``. We'll skip that here. Now, verify that the IP resource has been added, and display the cluster's status to see that it is now active. Note: There should be a stonith device by now, but it's okay if it doesn't look like the one below. .. code-block:: console [root@pcmk-1 ~]# pcs status Cluster name: mycluster Cluster Summary: * Stack: corosync * Current DC: pcmk-1 (version 2.1.2-4.el9-ada5c3b36e2) - partition with quorum * Last updated: Wed Jul 27 00:37:28 2022 * Last change: Wed Jul 27 00:37:14 2022 by root via cibadmin on pcmk-1 * 2 nodes configured * 2 resource instances configured Node List: * Online: [ pcmk-1 pcmk-2 ] Full List of Resources: * fence_dev (stonith:some_fence_agent): Started pcmk-1 * ClusterIP (ocf:heartbeat:IPaddr2): Started pcmk-2 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled On the node where the ``ClusterIP`` resource is running, verify that the address has been added. .. code-block:: console [root@pcmk-2 ~]# ip -o addr show 1: lo inet 127.0.0.1/8 scope host lo\ valid_lft forever preferred_lft forever 1: lo inet6 ::1/128 scope host \ valid_lft forever preferred_lft forever 2: enp1s0 inet 192.168.122.102/24 brd 192.168.122.255 scope global noprefixroute enp1s0\ valid_lft forever preferred_lft forever 2: enp1s0 inet 192.168.122.120/24 brd 192.168.122.255 scope global secondary enp1s0\ valid_lft forever preferred_lft forever 2: enp1s0 inet6 fe80::5054:ff:fe95:209/64 scope link noprefixroute \ valid_lft forever preferred_lft forever Perform a Failover ################## Since our ultimate goal is high availability, we should test failover of our new resource before moving on. First, from the ``pcs status`` output in the previous step, find the node on which the IP address is running. You can see that the status of the ``ClusterIP`` resource is ``Started`` on a particular node (in this example, ``pcmk-2``). Shut down ``pacemaker`` and ``corosync`` on that machine to trigger a failover. .. code-block:: console [root@pcmk-2 ~]# pcs cluster stop pcmk-2 pcmk-2: Stopping Cluster (pacemaker)... pcmk-2: Stopping Cluster (corosync)... .. NOTE:: A cluster command such as ``pcs cluster stop `` can be run from any node in the cluster, not just the node where the cluster services will be stopped. Running ``pcs cluster stop`` without a ```` stops the cluster services on the local host. The same is true for ``pcs cluster start`` and many other such commands. Verify that ``pacemaker`` and ``corosync`` are no longer running: .. code-block:: console [root@pcmk-2 ~]# pcs status Error: error running crm_mon, is pacemaker running? Could not connect to pacemakerd: Connection refused crm_mon: Connection to cluster failed: Connection refused Go to the other node, and check the cluster status. .. code-block:: console [root@pcmk-1 ~]# pcs status Cluster name: mycluster Cluster Summary: * Stack: corosync * Current DC: pcmk-1 (version 2.1.2-4.el9-ada5c3b36e2) - partition with quorum * Last updated: Wed Jul 27 00:43:51 2022 * Last change: Wed Jul 27 00:43:14 2022 by root via cibadmin on pcmk-1 * 2 nodes configured * 2 resource instances configured Node List: * Online: [ pcmk-1 ] * OFFLINE: [ pcmk-2 ] Full List of Resources: * fence_dev (stonith:some_fence_agent): Started pcmk-1 * ClusterIP (ocf:heartbeat:IPaddr2): Started pcmk-1 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled Notice that ``pcmk-2`` is ``OFFLINE`` for cluster purposes (its ``pcsd`` is still active, allowing it to receive ``pcs`` commands, but it is not participating in the cluster). Also notice that ``ClusterIP`` is now running on ``pcmk-1`` -- failover happened automatically, and no errors are reported. .. topic:: Quorum If a cluster splits into two (or more) groups of nodes that can no longer communicate with each other (a.k.a. *partitions*), *quorum* is used to prevent resources from starting on more nodes than desired, which would risk data corruption. A cluster has quorum when more than half of all known nodes are online in the same partition, or for the mathematically inclined, whenever the following inequality is true: .. code-block:: console total_nodes < 2 * active_nodes For example, if a 5-node cluster split into 3- and 2-node paritions, the 3-node partition would have quorum and could continue serving resources. If a 6-node cluster split into two 3-node partitions, neither partition would have quorum; Pacemaker's default behavior in such cases is to stop all resources, in order to prevent data corruption. Two-node clusters are a special case. By the above definition, a two-node cluster would only have quorum when both nodes are running. This would make the creation of a two-node cluster pointless. However, Corosync has the ability to require only one node for quorum in a two-node cluster. The ``pcs cluster setup`` command will automatically configure ``two_node: 1`` in ``corosync.conf``, so a two-node cluster will "just work". .. NOTE:: You might wonder, "What if the nodes in a two-node cluster can't communicate with each other? Wouldn't this ``two_node: 1`` setting create a split-brain scenario, in which each node has quorum separately and they both try to manage the same cluster resources?" As long as fencing is configured, there is no danger of this. If the nodes lose contact with each other, each node will try to fence the other node. Resource management is disabled until fencing succeeds; neither node is allowed to start, stop, promote, or demote resources. After fencing succeeds, the surviving node can safely recover any resources that were running on the fenced node. If the fenced node boots up and rejoins the cluster, it does not have quorum until it can communicate with the surviving node at least once. This prevents "fence loops," in which a node gets fenced, reboots, rejoins the cluster, and fences the other node. This protective behavior is controlled by the ``wait_for_all: 1`` option, which is enabled automatically when ``two_node: 1`` is configured. If you are using a different cluster shell, you may have to configure ``corosync.conf`` appropriately yourself. Now, simulate node recovery by restarting the cluster stack on ``pcmk-2``, and check the cluster's status. (It may take a little while before the cluster gets going on the node, but it eventually will look like the below.) .. code-block:: console [root@pcmk-1 ~]# pcs status Cluster name: mycluster Cluster Summary: * Stack: corosync * Current DC: pcmk-1 (version 2.1.2-4.el9-ada5c3b36e2) - partition with quorum * Last updated: Wed Jul 27 00:45:17 2022 * Last change: Wed Jul 27 00:45:01 2022 by root via cibadmin on pcmk-1 * 2 nodes configured * 2 resource instances configured Node List: * Online: [ pcmk-1 pcmk-2 ] Full List of Resources: * fence_dev (stonith:some_fence_agent): Started pcmk-1 * ClusterIP (ocf:heartbeat:IPaddr2): Started pcmk-1 Daemon Status: corosync: active/disabled pacemaker: active/disabled pcsd: active/enabled .. index:: stickiness Prevent Resources from Moving after Recovery ############################################ In most circumstances, it is highly desirable to prevent healthy resources from being moved around the cluster. Moving resources almost always requires a period of downtime. For complex services such as databases, this period can be quite long. To address this, Pacemaker has the concept of resource *stickiness*, which controls how strongly a service prefers to stay running where it is. You may like to think of it as the "cost" of any downtime. By default, [#]_ Pacemaker assumes there is zero cost associated with moving resources and will do so to achieve "optimal" [#]_ resource placement. We can specify a different stickiness for every resource, but it is often sufficient to change the default. -In |CFS_DISTRO| |CFS_VERSION|, the cluster setup process automatically +In |CFS_DISTRO| |CFS_DISTRO_VER|, the cluster setup process automatically configures a default resource stickiness score of 1. This is sufficient to prevent healthy resources from moving around the cluster when there are no user-configured constraints that influence where Pacemaker prefers to run those resources. .. code-block:: console [root@pcmk-1 ~]# pcs resource defaults Meta Attrs: build-resource-defaults resource-stickiness=1 For this example, we will increase the default resource stickiness to 100. Later in this guide, we will configure a location constraint with a score lower than the default resource stickiness. .. code-block:: console [root@pcmk-1 ~]# pcs resource defaults update resource-stickiness=100 Warning: Defaults do not apply to resources which override them with their own defined values [root@pcmk-1 ~]# pcs resource defaults Meta Attrs: build-resource-defaults resource-stickiness=100 .. [#] Zero resource stickiness is Pacemaker's default if you remove the default value that was created at cluster setup time, or if you're using an older version of Pacemaker that doesn't create this value at setup time. .. [#] Pacemaker's default definition of "optimal" may not always agree with yours. The order in which Pacemaker processes lists of resources and nodes creates implicit preferences in situations where the administrator has not explicitly specified them.