diff --git a/src/sbd.sysconfig b/src/sbd.sysconfig
index e661f96..f163f21 100644
--- a/src/sbd.sysconfig
+++ b/src/sbd.sysconfig
@@ -1,96 +1,99 @@
 ## Type: string
 ## Default: ""
 #
 # SBD_DEVICE specifies the devices to use for exchanging sbd messages
 # and to monitor. If specifying more than one path, use ";" as
 # separator.
 #
 #SBD_DEVICE=""
 
 ## Type: yesno
 ## Default: yes
 #
 # Whether to enable the pacemaker integration.
 #
 SBD_PACEMAKER=yes
 
 ## Type: list(always,clean)
 ## Default: always
 #
 # Specify the start mode for sbd. Setting this to "clean" will only
 # allow sbd to start if it was not previously fenced. See the -S option
 # in the man page.
 #
 SBD_STARTMODE=always
 
 ## Type: yesno / integer
 ## Default: no
 #
 # Whether to delay after starting sbd on boot for "msgwait" seconds.
 # This may be necessary if your cluster nodes reboot so fast that the
 # other nodes are still waiting in the fence acknowledgement phase.
 # This is an occasional issue with virtual machines.
 #
 # This can also be enabled by being set to a specific delay value, in
 # seconds. Sometimes a longer delay than the default, "msgwait", is
 # needed, for example in the cases where it's considered to be safer to
 # wait longer than:
 # corosync token timeout + consensus timeout + pcmk_delay_max + msgwait
 #
 # Be aware that the special value "1" means "yes" rather than "1s".
 #
 # Consider that you might have to adapt the startup-timeout accordingly
 # if the default isn't sufficient. (TimeoutStartSec for systemd)
 #
 # This option may be ignored at a later point, once pacemaker handles
 # this case better.
 #
 SBD_DELAY_START=no
 
 ## Type: string
 ## Default: /dev/watchdog
 #
 # Watchdog device to use. If set to /dev/null, no watchdog device will
 # be used.
 #
 SBD_WATCHDOG_DEV=/dev/watchdog
 
 ## Type: integer
 ## Default: 5
 #
 # How long, in seconds, the watchdog will wait before panicking the
 # node if no-one tickles it.
 #
 # This depends mostly on your storage latency; the majority of devices
 # must be successfully read within this time, or else the node will
 # self-fence.
 #
 # If your sbd device(s) reside on a multipath setup or iSCSI, this
 # should be the time required to detect a path failure.
 #
+# Be aware that watchdog timeout set in the on-disk metadata takes
+# precedence.
+#
 SBD_WATCHDOG_TIMEOUT=5
 
 ## Type: string
 ## Default: "flush,reboot"
 #
 # Actions to be executed when the watchers don't timely report to the sbd
 # master process or one of the watchers detects that the master process
 # has died.
 #
 # Set timeout-action to comma-separated combination of
 # noflush|flush plus reboot|crashdump|off.
 # If just one of both is given the other stays at the default.
 #
 # This doesn't affect actions like off, crashdump, reboot explicitly
 # triggered via message slots.
 # And it does as well not configure the action a watchdog would
 # trigger should it run off (there is no generic interface).
 #
 SBD_TIMEOUT_ACTION=flush,reboot
 
 ## Type: string
 ## Default: ""
 #
 # Additional options for starting sbd
 #
 SBD_OPTS=