Page MenuHomeClusterLabs Projects

Guest Fencing
Updated 342 Days AgoPublic

Pacemaker can use fence_virtd to fence nodes that are virtual machines. In such a setup:

  • The physical host does not need to run Pacemaker, and runs fence_virtd to accept fencing requests.
  • The virtual hosts do run Pacemaker, and initiate fencing requests.

Assumptions

This walk-through makes certain assumptions for simplicity:

  • All virtual machines run on the same physical host. (This is appropriate for a test environment, but in a production environment, the physical host would become a single point of failure.)
  • The physical host and virtual machines run RHEL 7 (for example commands, but the concepts apply to any distribution and should be easily adaptable).
  • The virtual machines do not have addresses on the local LAN, but instead use a virtual bridge virbr0 to communicate with each other and the physical host, which they use as their gateway.
  • fence_virtd will use multicast IP for communication, so Pacemaker will use the fence_xvm fencing device. (fence_virtd also supports fence_virt for communication via serial or VMChannel, which are not covered here.)

Choose a multicast address and a TCP port

fence_virtd will use a multicast IP address to communicate among the host and VMs. It will also contact clients directly on a TCP port when sending replies to requests.

By default, the multicast address is 225.0.0.12, and the TCP port is 1229.

You can choose other values if you prefer. In particular, choosing a multicast address describes common pitfalls, and a better choice might be in the site-local (239.255.x.y) or organization-local (239.192-251.x.y) ranges.

Configure the physical host

  • Install the software:
yum install fence-virt fence-virtd fence-virtd-multicast fence-virtd-libvirt
  • If a local firewall is enabled, allow traffic involving the chosen multicast IP. For simplicity, here we allow all traffic on the virtual bridge (which is appropriate only if you trust all VMs to the same degree as the host):
firewall-cmd --permanent --zone=trusted --change-interface=virbr0
  • Run the configuration tool:
fence_virtd -c

Accept all the defaults except for the items listed below, and the multicast IP and TCP port if you selected non-default ones:

Setting a preferred interface causes fence_virtd to listen only on that interface. Normally, it listens on all interfaces. In environments where the virtual machines are using the host machine as a gateway, this *must* be set (typically to virbr0). Set to 'none' for no interface.

Interface [none]: virbr0
You can accept the default (none) if the guests have IPs on the local LAN. Here, we assume they do not.
Key File [none]: /etc/cluster/fence_xvm.key

This ensures only machines with the same key can initiate fencing requests.

At the end, it will ask

Replace /etc/fence_virt.conf with the above [y/N]? y

Say yes.

  • You should end up with a configuration like this in /etc/fence_virt.conf:
backends {
  libvirt {
    uri = "qemu:///system";
  }
}
listeners {
  multicast {
    key_file = "/etc/cluster/fence_xvm.key";
    interface = "virbr0";
    port = "1229";
    address = "225.0.0.12";
    family = "ipv4";
  }
}

fence_virtd {
  backend = "libvirt";
  listener = "multicast";
  module_path = "/usr/lib64/fence-virt";
}
  • Create a random shared key:
mkdir -p /etc/cluster
touch /etc/cluster/fence_xvm.key
chmod 0600 /etc/cluster/fence_xvm.key
dd if=/dev/urandom bs=512 count=1 of=/etc/cluster/fence_xvm.key
  • Enable the daemon to start at boot, and start it:
systemctl enable --now  fence_virtd.service
  • Test the host's multicast connectivity (if you chose a non-default multicast address, specify it via the -a $MULTICAST_IP argument):
fence_xvm -o list

You should see output like:

[root@myhost ~]# fence_xvm -o list

pcmk-1               17bd6b6a-928f-2820-64ac-7c8d536df65f on
pcmk-2               f0062842-0196-7ec1-7623-e5bbe3a6632c on
pcmk-3               33e954b8-39ae-fb4b-e6e8-ecc443516b92 on
pcmk-4               98cda6de-74c4-97bf-0cfb-3954ff76a5c3 on

Remote: Operation was successful

Configure the virtual machine

  • Install the software:
yum install fence-virt fence-virtd
  • If a local firewall is enabled, open the chosen TCP port (in this example, the default of 1229) to the host (in this example 192.168.122.1):
firewall-cmd --permanent --add-rich-rule='rule family="ipv4" source address="192.168.122.1" port port="1229" protocol="tcp" accept'
firewall-cmd --reload
  • Create a place for the shared key:
mkdir -p /etc/cluster
  • Copy the shared key from the host to /etc/cluster/fence_xvm.key.
  • Test the guest's multicast connectivity (if you chose a non-default multicast address, specify it via the -a $MULTICAST_IP argument):
fence_xvm -o list

You should see the same output as you saw on the host, e.g.:

[root@pcmk-1 ~]# fence_xvm -o list
pcmk-1               17bd6b6a-928f-2820-64ac-7c8d536df65f on
pcmk-2               f0062842-0196-7ec1-7623-e5bbe3a6632c on
pcmk-3               33e954b8-39ae-fb4b-e6e8-ecc443516b92 on
pcmk-4               98cda6de-74c4-97bf-0cfb-3954ff76a5c3 on

Remote: Operation was successful

Configure Pacemaker

  • On any Pacemaker node, create the fencing resource:
pcs stonith create Fencing fence_xvm ip_family="ipv4" 
pcs property set stonith-enabled=true

If you chose a non-default multicast address and/or TCP port, add multicast_address="$MULTICAST_IP" and/or ipport=$TCP_PORT to the create line. See pcs stonith describe fence_xvm for more options.

  • Test the configuration by fencing a node:
pcs cluster standby $NODE_NAME
stonith_admin --reboot $NODE_NAME

Alternative configuration for guests running on multiple hosts

Not yet supported. Rough commands:

yum install -y libvirt-qpid qpidd
chkconfig --level 2345 qpidd on
chkconfig --level 2345 libvirt-qpid on
service qpidd start
service libvirt-qpid start
sed -i.sed s/libvirt/libvirt-qpid/g /etc/fence_virt.conf

See also

Last Author
kgaillot
Last Edited
Oct 31 2023, 5:06 PM